ENC10/12

28878

Replacement Enclosure Humidity Indicator Card

The 28878 is a replacement humidity indicator card. It provides a visual reference of humidity level inside the enclosure. Colored circles change color from blue to pink to indicate humidity levels of 30%, 40%, and 50% relative humidity. Double sticky tape on the back of the card allows it to be easily secured to an enclosure lid.

6316

Universal Backplate for ENC10/12

The 6316 provides a universal backplate for retrofitting older 10" x 12" enclosures. The anodized aluminum backplate is completely pre-punched with a matrix of half-inch-on-center holes. The 6316 replaced the now-retired 5947 Half Universal Backplate, which contained press-in hardware for the CR10 and 21X (upper half) and a grid of one-inch-on-center holes (lower half).

Another backplate used in the ENC10/12 is also retired; the 5622 backplate had a special hole configuration that supported the AM32 multiplexer (the AM32 was a much larger predecessor of the AM16/32B).

6832

Enclosure Filter with 60 Micron Pore Size

One 6832 filter may be installed in one of the small compression fittings (cable entry seals) in the ENC10/12 to allow air pressure to equalize between the inside and outside of the enclosure. As such, the filter is used only when the cable entry seals option is selected for the enclosure (item 6447). The filter is typically used when a barometric pressure sensor (or, in some cases, the cable termination of a vented submersible pressure transducer) will be located inside the enclosure. The filter has a 60 micron pore size.

18955

ENC10/12 Tripod Leg Mounting Kit

The 18955 provides the same bracket as "-LM" mounting option. This bracket may be ordered as a replacement part, if the bracket gets damaged, or if another option was originally chosen. The 18955 allows the enclosure to be attached to the leg base of a CM110, CM115, or CM120 lightweight tripod.

795

Stainless-Steel Nylock Nut 1/4-20

A couple of these nuts are attached to the enclosure bracket. The nut may be purchased to replace a lost or damaged nut.

5449

Enclosure Ground Lug

The 5449 ground lug is attached to the enclosure. It may be purchased to replace a lost or damaged ground lug.

23

Stainless-Steel Nut #10-32

The pn 23 nut is available as a replacement item.

7363

Enclosure Supply Kit, Standard Size

The enclosure supply kit includes desiccant, a humidity indicator card, cable ties, wire tie tabs, putty for sealing the conduit, and screws and grommets for attaching peripherals to the enclosure backplate.

25744

1-1/2 Panel Bushing Pin (Male)

The 25744 and 25746 are the two parts used to create the standard conduit for Campbell Scientific enclosures. If a portion of the conduit for an ENC or PWENC enclosure becomes lost, the 25744 and 25746 can be ordered as replacements.

25746

1-1/2 PVC Coupling PVC Female Adapter

The 25746 and 25744 are the two parts used to create the standard conduit for Campbell Scientific enclosures. If a portion of the conduit for an ENC or PWENC enclosure becomes lost, the 25746 and 25744 can be ordered as replacements.

560

Screw #10-32 x .312 Pan Phillips

The 560 screw is used to attach a backplate to the inside of an enclosure.

5725

14 AWG Enclosure Ground Wire, 24 in. long

This 14 gauge ground wire connects the enclosure ground lug to the datalogger.

3890

Silicone O-Ring

The 3890 is a silicone O-ring used. Customers will periodically need to replace worn-out O-rings.

6688

Plug for Cable Entry Connector

The 6688 is the plug that fits inside the 31363 Cable Entry Seal when there is not a cable running through it. The 6688 can be ordered to replace a lost plug.