CR1000

17315

Peripheral Port Cover for the CR1000 or CR3000

The 17315 protects the peripheral port and may be purchased to replace a lost or damaged cover.

10645

Screw #10-32 x .312 Pan Slot, Brass

The 10645 is the screw used in the ground lug.

13519

Replacement Lithium Battery

The 13519 fits inside of the CR1000 module. This lithium battery powers the clock and SRAM when the primary 12 Vdc power supply is not connected. The 13519 can be replaced by the user; the process is illustrated in the CR1000 Operator's Manual.

42900

Battery and Desiccant Kit for the CR800-Series and CR1000 Dataloggers

The 42900 kit provides a replacement battery and desiccant for the CR800-series and CR1000 dataloggers. The kit consists of a single 0.16-unit silica desiccant bag and a 3.6 V 1.2 Ah lithium AA battery. When shipped, the data logger has one bag of this desiccant inside it. While the supplied desiccant should fill the initial needs of most applications, it should be periodically replaced. Campbell Scientific recommends replacing this desiccant when the data logger's internal lithium battery is replaced.

3768

2-Pin Screw Terminal Plug Connector

The 3768 is shipped attached to the CR1000. This green, plug-in power connector provides screw terminals for connecting the 12 V and GND wires of the data logger's power supply. The 3768 may be purchased to replace a lost or damaged power connector.

8125

Flat-Bladed Screwdriver, 2.5 mm Blade x 50 mm Shaft

The 8125 is a small, flat-bladed screwdriver that is extremely useful for opening the guillotine terminals on our data loggers and measurement control devices.

10873

Serial Data Cable, 9-Pin Socket (Female) to 9-Pin Pin (Male)

The 10873 is a serial cable that is useful for connecting the RS-232 port of the data logger to the 9-pin RS-232 port of a computer. The cable is six feet long.

6044

Grommet for #6 or #8 Screw

These grommets are commonly used with the 505 screws to secure our equipment to the backplates of our enclosures.

505

Screw #6-32 x .375 Pan Phillips

These screws, along with the 6044 grommets, are commonly used together to secure our equipment to the backplates of our enclosures.

3315

Type T Thermocouple

This type T, 5 in. thermocouple is attached to a differential channel on several of our data logger wiring panels when the data logger is shipped. A 3315 may be ordered to replace a thermocouple that has become lost or damaged.

17749

CR1000 Calibration with Data (-25° to +50°C)

The 17749 requires an RMA (Return Material Authorization) from Campbell Scientific. When ordered, we calibrate the CR1000 to meet original specifications. Calibration includes standard temperature testing (-25° to +50°C). Before and after calibration sheets are supplied with the CR1000.

17750

CR1000 Extended Temperature Test (-55° to +85°C)

Testing is available only for individual units that have previously passed Extended Temperature Testing. Testing also requires concurrent purchase of calibration. An RMA (Return Material Authorization) from Campbell Scientific is required.

17787

Onsite Training Class, 4 Days, CR1000X, by 1 Support and Implementation Specialist

If you have a large group of individuals who require standard or custom training, it may be cost-effective for us to come to you. This class includes 4 days of training on the CR1000 and LoggerNet. One Applications Engineer conducts the training (5 people maximum). Our travel expenses within the continental United States are included, as are use of data loggers, computers, software, sensors, and instructional materials. Our training materials are shipped in cases that contain 3 training set-ups per case; we have four cases available for training.

17788

Onsite Training Class, 4 Days, CR1000X, by 2 Support and Implementation Specialists

This class includes 4 days of training on the CR1000 and LoggerNet. Two Applications Engineers conduct the training (11 people maximum). Our travel expenses within the continental United States are included, as are use of data loggers, computers, software, sensors, and instructional materials. Our training materials are shipped in cases that contain 3 training set-ups per case; we have four cases available for training.

17789

Training Class at Campbell Scientific, 4 Days, CR1000/LoggerNet, for 1 Person

We offer training courses at our factory in Logan, Utah. Price includes 4 days of instruction on the CR1000 Datalogger and LoggerNet software, and allows the use of training computers, data loggers, and facilities. Travel and accommodations are NOT included. Lunch will be provided by CSI on each day of class.

34152

CR1000 Calibration over Temperature and ISO/IEC 17025 Calibration Verification with Certificate

The 34152 provides factory calibration of the CR1000 to meet original specifications, then sends the calibrated data logger to be verified by a certifying body that is accredited to the ISO 17025 standards.

This service requires an RMA (Return Material Authorization) from Campbell Scientific. The factory calibration includes comprehensive testing of all data logger functions over its standard temperature range (-25° to +50°C) and the replacement of the internal lithium battery and desiccant packs. During testing, the data logger’s operating system is updated, and all settings are restored to factory defaults unless otherwise requested. Upon completion of the factory calibration, the data logger is sent to the ISO 17025 accredited certifying body referenced above for calibration verification.