PWENC16/18
PWENC16/18
OrderablePrewired Enclosure, 16 x 18 inches
Pricing
Configuration
Sign in for option pricing- PWENC16/18 Pre-Wired Weather-Resistant 16 X 18 Inch Enclosure NOTE: Not Cancelable or Returnable ProductSP45283-C11-2P-SC-ME-ER-LM-2SGH
- PWENC16/18 Pre-Wired Weather-Resistant 16 X 18 Inch Enclosure NOTE: Not Cancelable or Returnable ProductSP45283-C12-NP-SC-ME-ER-MM-1SGH
- PWENC16/17 Pre-Wired Weather-Resistant 16 X 18 Inch EnclosureSP45283-C14-NP-NC-NE-ER-NM-1SGH
- PWENC16/17 Pre-Wired Weather-Resistant 16 X 18 Inch EnclosureSP45283-C15-NP-NC-NE-ER-MM-1SGH
- PWENC16/17 Pre-Wired Weather-Resistant 16 X 18 Inch EnclosureSP45283-C8-NP-SC-NE-ER-MM-NA
- PWENC16/18 Pre-Wired Weather-Resistant 16 X 18 Inch EnclosureSP45283-C6-NP-NC-NE-ER-NM-2SGH
- PWENC16/18 Pre-Wired Weather-Resistant 16 X 18 Inch Enclosure NOTE: Not Cancelable or Returnable ProductSP45283-C8-NP-SC-NE-ER-LM-NA
- PWENC16/17 Pre-Wired Weather-Resistant 16 X 18 Inch EnclosureSP45283-C8-NP-NC-NE-ER-NM-NA
- PWENC16/18 Pre-Wired Weather-Resistant 16 X 18 Inch EnclosureSP45283-C8-2P-NC-NE-ER-NM-NA
- PWENC16/18 Pre-Wired Weather-Resistant 16 X 18 Inch EnclosureSP45283-C6-NP-SC-NE-ER-MM-NA
Select a configuration to add to your quote
- Model:
- PWENC16/18
- Item Number:
- SP45283
- Warranty:
- 1 year
Overview
The PWENC16/18 is a prewired, weather-resistant enclosure that is 16 in. wide and 18 in. tall. It starts with the same enclosure used for our ENC16/18, but then is factory configured with up to 19 connectors that are attached to the data logger or peripherals within the enclosure. Sensors with the appropriate connector are simply attached to connectors on the outside of the enclosure. The PWENC16/18 includes a basic measurement program (created in ShortCut) for the -PW products sold as part of this system. If a more advanced custom data logger program is required for additional sensors, communications, control, or other needs, an extra fee will be incurred.
Key Advantages
Factory-installed and tested wiring by experienced technicians
Technical Description
The PWENC16/18 can house one data logger, power supply, and one or more peripheral (depending on the peripheral’s footprint). You order the sensors, data logger, power supply, and communication peripherals separately. Compatible sensors, peripheral cables, and solar panels have a –PW extension.
The PWENC16/18 is shipped with the 7363 enclosure supply kit that consists of desiccant, a humidity indicator card, cable ties, wire tie tabs, putty, grommets, screws, and PVC coupling. Connectors, communication ports, and the enclosure mounting bracket are chosen as options. (See Ordering Info on the web page.)
The PWENC16/18 can be mounted to any of our tripods or towers, or to a user-supplied pipe.
Note: Refer to the Ordering Info on the web page for standard configurations. Nonstandard configurations must be special ordered. It is considered a nonstandard configuration when using a different type, size, or location for any connector, communication port, conduit, cable entry seal, or antenna bulkhead (contact Campbell Scientific for more information).
Benefits
- Weather resistant to protect instruments
- Backplate designed so that Campbell Scientific components mount easily and securely
- Combines flexibility with ease of use
- Eliminates the task of wiring sensor leads into the data logger’s terminal strips
- Reduces wiring errors by inexperienced field technicians who are unfamiliar with the equipment
- Shortens deployment time
- Allows each enclosure in a large network to be similar to the other enclosures
- Customized options may be purchased
- White, UV-stabilized enclosure reflects solar radiation—reducing temperature gradients inside the enclosure without requiring a separate radiation shield
Specifications
- Color
- White
(Reflects solar radiation, reducing temperature gradients inside the enclosure without using a separate radiation shield.)
- Construction
- Fiberglass-reinforced polyester enclosure with door gasket, external grounding lug, stainless-steel hinge, and lockable hasps
- Enclosure Classification
- NEMA 4X
(before being modified for cable entry)
- Dimensions
- 45.7 x 40.6 x 22.9 cm
(18 x 16 x 9 in.) internal
43.8 x 38.7 x 25.2 cm(17.3 x 15.3 x 9.9 in.) internal under the lid space
49.5 x 44.4 x 27 cm(19.5 x 17.5 x 10.6 in.) external
- Weight
- 7.7 kg
(17 lb)
Accessories
(6)6714
Four-Unit Desiccant Bags (quantity of 20)
Orderable42815
Four-Unit Desiccant Bags (quantity of 10)
Orderable10614
Direct Wire Bury Splice Kit (includes 2 wires)
OrderableCOMCBL2
Weatherproof Cable, 9-Pin Pin (Male) to 9-Pin Socket (Female)
Orderable31551
Enclosure Leg Stack Mounting Kit
Orderable31143
Hinged Enclosure Stack Mounting Kit
Orderable
Common Accessories
(5)6714
Four-Unit Desiccant Bags (quantity of 20)
The 6714 includes twenty 4-unit Silica Gel Desiccant Bags.
Orderable42815
Four-Unit Desiccant Bags (quantity of 10)
The 42815 includes 10 large, four-unit desiccant bags, used to absorb humidity within enclosures. Multiple packs are recommended for customers who need to desiccate multiple enclosures or systems.
Orderable31551
Enclosure Leg Stack Mounting Kit
The 31551 is a kit to allow stacking of components inside Campbell Scientific enclosures. The kit includes two leg brackets. It is used to raise a datalogger up and off the backplate so that wiring is easier or so that components can be stacked.
Orderable31143
Hinged Enclosure Stack Mounting Kit
The 31143 is a hinged stack bracket that is designed to fit a CR1000 datalogger, CR6 datalogger, or multiplexter on either the top or underneath. The hinge enables access to the equipment underneath without disconnecting any wires (assuming that the wires are long enough).
Orderable10614
Direct Wire Bury Splice Kit (includes 2 wires)
This splice kit is used when you need to extend the cables outside of the enclosure.
Orderable
Replacement Parts
(9)5449
Enclosure Ground Lug
The 5449 ground lug is attached to the enclosure. It may be purchased to replace a lost or damaged ground lug.
Orderable23
Stainless-Steel Nut #10-32
The pn 23 nut is available as a replacement item.
Orderable7363
Enclosure Supply Kit, Standard Size
The enclosure supply kit includes desiccant, a humidity indicator card, cable ties, wire tie tabs, putty for sealing the conduit, and screws and grommets for attaching peripherals to the enclosure backplate.
Orderable22035
PWENC Internal Power Cable with Connector, 36 in.
The 22035 may be ordered to replace a lost or damaged cable.
Orderable25744
1-1/2 Panel Bushing Pin (Male)
The 25744 and 25746 are the two parts used to create the standard conduit for Campbell Scientific enclosures. If a portion of the conduit for an ENC or PWENC enclosure becomes lost, the 25744 and 25746 can be ordered as replacements.
Orderable25746
1-1/2 PVC Coupling PVC Female Adapter
The 25746 and 25744 are the two parts used to create the standard conduit for Campbell Scientific enclosures. If a portion of the conduit for an ENC or PWENC enclosure becomes lost, the 25746 and 25744 can be ordered as replacements.
Orderable560
Screw #10-32 x .312 Pan Phillips
The 560 screw is used to attach a backplate to the inside of an enclosure.
Orderable6650
Enclosure Ground Wire, 36 in.
This 36 in.ground wire and lug connector can be purchased to replace a ground wire and lug connector that has been lost or damaged.
Orderable40031
32 GB USB Flash Drive Dual Type A and C Connectors, Gray/Silver
The 40031 is a 32 GB gray/silver flash drive with the Campbell Scientific logo on it. The drive has dual USB A and C connectors for enhanced functionality. It is useful for transferring files, such as program files, for users who do not have a CD/DVD drive but do have a USB port.
Orderable
Compatibility
Peripherals
Our prewired enclosures can house any peripheral that our standard enclosures can house. Equipment that can be attached to the outside of the prewired enclosure include:
- Sensors—models with an -PW extension are compatible; a -PW version is available for most Campbell Scientific sensors.
- Digital camera—the cable used to connect a CC5MPX or CC5MPXWD high-resolution digital camera has a -PW cable termination option.
- AC wall charger—the 22110 Wall Charger (accepts 110 to 240 Vac) has the appropriate connector.
- Solar panels—Campbell Scientific offers -PW versions of our 10 W, 20 W, 50 W, and 90 W solar panels.
- Keyboard display—the CR1000KD can be connected via an optional CS I/O port.
- Laptop—an RS-232 or CS I/O port can be added to the outside of the enclosure allowing laptop connection.
- Ethernet cable—an optional Ethernet port is offered that supports communications over a local network or a dedicated Internet connection.
- Antennas—the outside of the enclosure can include connectors for attaching antenna cables.
- Measurement and control peripherals—cables used to connect our SDMs and multiplexers come in -PW versions.
