Limited Availability ›
This product has limited availability. Some accessories, replacement parts, or services may still be available when it is no longer available.
SR50AT-316SS-L
 
SR50AT-316SS-L CSC Stainless Steel Sonic Ranging Sensor for Marine Environments w/Temp Sensor
 
SR50AT-316SS-L Options - show details
-L ft cable per sensor

Allowed values: 0-1000 ft, increments of 1 ft

Cable Termination Options
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
-C -C w/ET/CS110 Connector

Add to your Quote List


Product Details
Restockable Yes
Warranty 2 years
Compliance CE Compliance Image RoHS Compliance Image
Ships With
(1) Test Report
(1) SR50ATCBL-L Replacement SR50AT Cable

Common Accessories

41303-5A
 
The 41303-5A is a naturally aspirated, 6-plate radiation shield. Its louvered construction allows air to pass freely through the shield, serving to keep the probe at or near ambient temperature. The shield's white color reflects solar radiation.
RAD06
 
The RAD06 uses a double-louvered design that offers improved sensor protection from driving rain, snow, and insect intrusion. It also has lower self-heating in bright sunlight combined with higher temperatures (> 24°C (~75°F)) and low wind speeds (< 2m/s (~4.5 mph)), providing a better measurement
19517
 
This mounting kit attaches directly to a CM206 crossarm or user-supplied pole with a 1-in. to 1.75-in. outside diameter.
19484
 
This mounting stem attaches to a sensor. The stem is then attached to the CM206 crossarm or a user-supplied pole via a CM220 mount, 17953 Nu-Rail fitting, or CM230 Adjustable Inclination Mount.
17953
 
The 17953 connects a vertical 1-inch pipe to a horizontal 1-inch pipe. The 17953 is typically used to attach a sensor with a 1-inch vertical pipe mount to a CM202, CM204, or CM206 crossarm. This usage provides functionality similar to the CM220 right-angle mounting bracket.
CM220
 
The CM220 right-angle mounting bracket can attach a sensor with a vertical pipe mount (e.g., most wind sensors) to a crossarm. It is compatible with pipes that have a 1- to 1.5-inch outer diameter.
CM230
 
The CM230 is an adjustable mount to point directional antennas or sensors at a specific target. The inclination can be adjusted to any angle from horizontal to vertical, supporting the use of upward-directed antennas or downward-directed infrared thermometers or snow-depth sensors.
CM230XL
 
The CM230XL is an adjustable mount to point directional antennas or sensors at a specific target. The inclination can be adjusted to any angle from horizontal to vertical, supporting the use of upward-directed antennas or downward-directed infrared thermometers or snow-depth sensors.

Other Accessories

33815
 
The 33815 makes it easier for you to connect wires from multiple SDI-12 sensors into one set of terminals on a data logger. The 33815 uses six DIN-rail mountable (pn 27479) 6-wire terminal blocks. The 33815 jumpers two connectors together at a time (pn 32918). This setup allows up to 11 SDI-12 sensors to be connected to one set of terminals on a data logger.

Replacement Parts

SR50ATCBL-L
 
SR50ATCBL-L Replacement SR50AT Cable
 
The cable may be ordered to replace a cable that has become lost or damaged.
SR50ATCBL-L Options - show details
-L ft per sensor cable

Allowed values: 1-1000 ft, increments of 1 ft

Cable Termination Options
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
-C -C w/ET/CS110 Connector
905
 
Two bags of the 905 desiccant are used inside the electronics housing. The 905 desiccant is not replaced when the transducer is replaced.
4091
 
Six bags of the 4091 desiccant are used to dry the air in the area above the transducer. Six bags are included in the transducer replacement kit.
32570
 
The 32570 kit includes a transducer housing, desiccant, and a replacement O-ring. It is recommended that the transducer housing assembly be replaced every three years, or annually in high-humidity environments.

Services

 
The 30249 is a service for the SR50A provided at the factory. All factory replacements require an RMA (Returned Material Authorization).