CSAT3BH
 
CSAT3BH 3-D Sonic Anemometer w/Heater & Integrated Electronics
 
Sonic Environment Option
-SE -SE for Std Environment
-HE -HE for Hash Environment
Carrying Case Option
-NC -NC No Carrying Case
-SC -SC CSAT3BH Carrying Case

Add to your Quote List


Product Details
Restockable Yes
Warranty 1 year
Compliance
Ships With
(1) 35244 Temperature and RH Sensor for CSAT3BH (with 41303-5A Shield)
(1) 30179 USB Data Cable, Type A Male to Type Mini-B Male, IP68, 5 m
(1) CM250 Leveling Mounting Kit
(1) 30749 CSAT3B(H) Replacement Desiccant
(1) 29191 CSAT3B(H) Foam Case Set
(1) 35792 CSAT3BH Quick Deploy Guide
(1) 35240 Heated Controller for CSAT3BH
(1) Certificate of Conformance

Common Accessories

CSAT3BCBL1-L
 
CSAT3BCBL1-L CSAT3B Power/SDM Cable
 
At least one of the CSAT3B cables is needed for each CSAT3BH. The CSAT3BCBL1-L is one option. The Power/SDM cable CSAT3BCBL1-L is used to deliver power and SDM communications to a CSAT3B. The -L denotes the length of cable in feet
CSAT3BCBL1-L Options - show details
-L ~Qft per sensor cable

Allowed values: 1-1000 ft, increments of 1 ft

Cable Termination Options
-PT -PT w/Tinned Wires
-MC -MC w/M16 IP68 Connector
CSAT3BCBL2-L
 
CSAT3BCBL2-L CSAT3B Power Only Cable
 
At least one of the CSAT3B cables is needed for each CSAT3BH. The CSAT3BCBL2-L is one option. The Power-Only Cable CSAT3BCBL2-L is used to deliver power to a CSAT3BH that will use CPI, USB, or RS-485 communications instead of SDM communications. The -L denotes the length of cable in feet.
CSAT3BCBL2-L Options - show details
-L ~Qft per sensor cable

Allowed values: 1-550 ft, increments of 1 ft

Although the maximum cable length is 550 feet, anyone requiring a cable length of 401 to 550 feet should use a 24 V power supply.
Cable Termination Options
-PT -PT w/Tinned Wires
-MC -MC w/M16 IP68 Connector
CSAT3BCBL3-L
 
CSAT3BCBL3-L CSAT3B CPI/RS-485 Cable
 
At least one of the CSAT3B cables is needed for each CSAT3BH. The CSAT3BCBL3-L is one option. The CPI/RS-485 cable CSAT3BCBL3-L is used to deliver CPI or CPI communications between a CSAT3BH and a data logger, another CSAT3BH, or a wiring hub. The -L denotes the length of cable in feet.
CSAT3BCBL3-L Options - show details
-L ~Qft per sensor cable

Allowed values: 1-1000 ft, increments of 1 ft

Cable Termination Options
-PT -PT w/Tinned Wires
-RJ -RJ w/RJ45 Connector
-MC -MC w/M16 IP68 Connector
CSAT3HCBL1-L
 
CSAT3HCBL1-L CSAT3H Control Box RS-485 TX/RX Cable
 
The CSAT3HCBL1-L provides communication between the data logger and the CSAT3H Controller Box via RS-485. The -L denotes the user-defined length of the cable between 1 and 300 feet (0.3 and 91.44 m).
Cable Length - show details
-L ~Qft per cable

Allowed values: 1-300 ft, increments of 1 ft

CSAT3HCBL2
 
The CSAT3HCBL2 is a 4.57 m (15 ft) cable that provides communication between a PC and a CSAT3H Controller Box via RS-485.

Note: You do not need the CSAT3HCBL2 to communicate with the controller box via a data logger. For this type of communication connection, use a CSAT3HCBL1-L instead.
CSAT3HCBL3-L
 
CSAT3HCBL3-L CSAT3H Control Box Power Cable
 
One CSAT3HCBL3-L is needed per CSAT3BH. The CSAT3HCBL3-L is used to provide a 24 Vdc power source to the CSAT3H Controller Box. The -L denotes the user-defined length of the cable between 1 and 30 feet (0.3 and 9.14 m).
Cable Length - show details
-L ~Qft per cable

Allowed values: 1-30 ft, increments of 1 ft

10080
 
The 10080 is a thermocouple cover for the FW05 connector.
FW05
 
Measures atmospheric temperature gradients or fluctuations with research-grade accuracy.
FW/ENC
 
Protects thermocouples during shipping and transport.
FWC-L
 
FWC-L Connector Cable for Fine Wire TCs
 
Connects a fine-wire thermocouple to a data logger.
Cable Length - show details
-L ~Qft cable per sensor

Allowed values: 1-1000 ft, increments of 1 ft

A 20 ft lead length (FWC-L20) is recommended for most applications.
31423
 
One 31423 is needed per fine-wire thermocouple. The 31423 is required to make the fine-wire thermocouple assembly compatible with the CSAT3BH.

Other Accessories

HUB-SDM8
 
The HUB-SDM8 is intended for customers who want to connect up to five external SDMs to the same data logger, as well as run multiple power connections using 16 AWG wire. The HUB-SDM8 comprises an environmental enclosure with eight compression fittings (two larger) and eight terminal strips.
CABLE5CBL-L
 
CABLE5CBL-L 5-Conductor 22AWG Cable w/Drain
 
The CABLE5CBL-L is a 22 AWG five-conductor cable used to connect the Power/SDM connections from a HUB-SDM8 to the Power and SDM connections on a power source and data logger.
CABLE5CBL-L Options - show details
-L ~Qft per cable

Allowed values: 1-1000 ft, increments of 1 ft

Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the data logger.
-PW -PW w/Pre-Wire Connector
Choose this option if you are using this cable with a pre-wired enclosure.
HUB-CPI
 
The HUB-CPI allows eight CPI (CAN peripheral interface) devices to be connected together in parallel. Typically, this configuration includes one data logger and up to seven CDMs (Campbell distributed modules) or sensors that use CPI.
29370
 
One 29370 kit is needed for each CPI network, such as those using a CDM-VW300, CDM-VW305, or SC-CPI. Among the items included in the 29370 kit is a roll of yellow vinyl electrical tape to distinguish Ethernet cables that use CPI protocol from similar cables used for TCP/IP.
28899
 
The 28899 is a 2 ft CAT6 Ethernet cable used to connect a HUB-CPI to a CPI socket on a dat alogger, or to connect one HUB-CPI to another HUB-CPI.

Replacement Parts

28902
 
Includes three upper transducer wicks, three lower transducer wicks, a wick-installation tool, and a small tube of adhesive to attach the wicks to the transducers.
 
The 30749 is a small cylindrical canister of desiccant that is used in the CSAT3BH to keep the internal electronics dry. The canister should be replaced as soon as the CSAT3BH internal relative humidity exceeds 25%, or when the silica gel changes in color from blue to pink.
 
The 30748 contains a bubble level and three screws. It is used to replace the bubble level on a CSAT3BH sonic anemometer.
35244
 
The 35244 is a temperature and relative humidity sensor with an R. M. Young Company six-plate radiation shield for use with the CSAT3BH. The 35244 provides critical temperature and relative humidity data to the CSAT3H Controller Box, which is then used to control the heaters within the heated sonic anemometers. Because the 35244 is included with the heated sonic anemometers, it is purchased as a replacement part, rather than as a stand-alone sensor.
29191
 
The 29191 is the foam set used to protect the CSAT3BH during transport and shipping.
41303-5A
 
The 41303-5A is a naturally aspirated, 6-plate radiation shield. Its louvered construction allows air to pass freely through the shield, serving to keep the probe at or near ambient temperature. The shield's white color reflects solar radiation.
30179
 
The 30179 is a 5 m (16 ft) USB cable. One end has a standard type A male connector for easy connection to a PC. The opposite end has a mini-B male connector for connecting to a USB port on a sensor, such as the CSAT3BH.
35240
 
The CSAT3H Heated Controller is a box with the electronics that control the heaters within the CSAT3BH. The CSAT3H is included with the CSAT3BH; however, it can be purchased separately if a replacement box is needed.
CM250
 
The CM250 is a mounting kit for several products that are mounted and leveled on the end of a crossarm. It consists of a fabricated aluminum adapter with set screws, a captive 3/8 in. bolt, and a 3/16 in. Allen wrench. The adapter is meant to be attached to the end of a 1.31 in. outer diameter pipe or crossarm, such as the CM204. The 3/16 in. Allen wrench may be used to tighten the pair set screws that hold the adapter in place on the crossarm. The captive 3/8 in. bolt screws into the block or base of the sensor being mounted. As the bolt is tightened, the base of the sensor and the top of the adapter form a ball-and-socket joint that can be adjusted until the sensor is level.
35634
 
The 35634 is a large, rugged carrying case without foam to accommodate a CSAT3BH and its accessories. Campbell Scientific recommends using this case when when transporting or shipping the CSAT3BH. The 35634 is intended for use with the foam inserts that were originally shipped with the CSAT3BH.
35633
 
The 35633 is a large, rugged carrying case with foam to accommodate a CSAT3BH and its accessories. Campbell Scientific recommends using this case when transporting or shipping the CSAT3BH.

Services

 
Provides calibration over the CSAT3BH operating temperature range without using the coordinate measurement machine (CMM). No documentation is provided.
 
Provides calibration over the CSAT3BH operating temperature range and coordinate measurement of transducer positions in space relative to the bubble mounting surface. A coordinate measurement machine (CMM) is used for this process. No documentation is provided.