CR9000XDC DC Datalogger Base System
Temperature Ranges
-ST -ST -25 to +50C
-XT -XT -40 to +70C
Warranty Lengths
-SW -SW Standard 3yr Warranty
-XW -XW 4yr Warr Extension
Calibration Certificate
-NC -NC No Calibration Cert
-CC -CC Calibration Cert
-LE -LE Lab Enclosure
-FE -FE Field Enclosure

Add to your Quote List

Product Details
Typically Ships Within 30 - 37 Days
Restockable Yes
Warranty 3 years

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.

Ships With
(1) Transformer w/power cord
(1) 8125 Flat-Bladed Screwdriver, 2.5 mm Blade x 50 mm Shaft
(1) 10873 Serial Data Cable, 9-Pin Female to 9-Pin Male

Common Accessories

RTDAQ Real-Time Data Acquisition Software
Need at least 1 copy.
Delivery Method
-D -D Download Only
-DD -DD Download & CD Disc
This 10baseT Ethernet straight through cable can be used when the cable is run from a hub to the CR9000XDC. The 28900 has a 10 ft length.
The 28901 is similar to the 28900 cable but has a 50 ft length. This cable is typically used when the distance between the hub and datalogger is 10 to 50 ft.
CAT5UCBL-L CAT5e Cable Unshielded w/RJ-45 Connectors
The CAT5UCBL is similar to the 28900 cable but is ordered to a user-defined length.
Cable Length - show details
-L ft per cable

Allowed values: 1-1000 ft, increments of 1 ft

The 13659 10baseT Ethernet Crossover Cable is required to configure the CR9000XDC's CR9032 IP connection directly from a PC's ethernet port. It has a 7 foot length.
The CF1 adapter allows the PCMCIA slots in the CR9000XDC to receive CompactFlash® cards. Only industrial-grade CF cards with a storage capacity of 2 GB or less should be used with our products.
The 17752 Reader/Writer allows a computer's USB port to read the data stored on CF card.
The CFMC256M is an industrial-grade CompactFlash card with a 256 MB storage capacity. The card is formatted as FAT32.
The CFMC2G is an industrial-grade CompactFlash card with a 2 GB storage capacity. The card is formatted as FAT32.

Replacement Parts

This "blank" (no circuit board or components) occupies one slot in the CR9000XDC chassis when the slot will be unoccupied by a functional I/O Module, thereby providing a degree of protection for modules in the adjacent slots.
This battery powers the clock and RAM when the primary 12 Vdc power supply is not connected. The battery must be replaced when its voltage falls below 2.4 Vdc.
The 10659 Strain Relief Adapter is attached to the chassis of a CR9000(X)-series datalogger, and then cable ties are used to fasten the cables to the adapter. By securing the cables to the datalogger's chassis, the likelihood that the sensor cables will be "jerked" out of their screw terminals is reduced.
CR9032 CR9000X CPU Module
The CR9032 CPU Module provides system control, processing, and communication to a PC via ethernet (10BaseT) or serial connection.
Temperature Ranges - show details
-ST -ST -25 to +50C
Every CR9032 is tested and guaranteed to perform within published specifications over the standard temperature range. Units are tested and shipped to standard operating range unless extended testing is specified. Batteries are not temperature tested.
-XT -XT -40 to +70C
For extended temperature range testing, analog accuracies are derated approximately two times over published specifications. Extended testing covers the -40‚° to +70‚°C range. Batteries are not temperature tested. Previously appeared on CR9032 orders as the XT-CR9032.
Warranty Lengths - show details
-SW -SW Standard 3yr Warranty
At the time of purchase, the CR9032 includes a standard warranty of 36 months. See our full warranty policy in the CR9000X manual for the terms and conditions of this warranty.
-XW -XW 4yr Warr Extension
Our Extended Warranty adds 48 months to the standard 36 month warranty, bringing the total warranty period to 84 months. The extended warranty may be purchased only at the time of original product purchase. It may NOT be "added later." Except for the increased coverage length, the same terms and conditions apply to the extended warranty as apply to the standard warranty.
The 13374 Power Supply Module provides regulated power to the CR9000XDC from the internal battery modules. It also regulates battery charging from power supplied by the ac adapter, a dc input, or other external sources.
The 10873 is a serial cable that is useful for connecting the RS-232 port of the datalogger to the 9-pin RS-232 port of a computer. The cable is six feet long.
The 8125 is a small, flat-bladed screwdriver that is extremely useful for opening the guillotine terminals on our dataloggers and measurement control devices.