Data Loggers / CR800
CR800
 
CR800 Measurement & Control Datalogger
 
Temperature Ranges - show details
-ST -ST -25 to +50C
Every CR800 is tested and guaranteed to perform within published specifications over the standard temperature range. Units are tested and shipped to the standard temperature range unless an extended range is specified. Any internal batteries are not tested or guaranteed across the entire standard temperature range.
-XT -XT -55 to +85C
When ordered, the CR800 is tested and guaranteed to perform over the extended temperature range. Analog accuracies are derated approximately two times over the published specifications. The extended testing covers the -55° to +85°C range. Any internal batteries are not tested or guaranteed across the entire extended temperature range.
Warranty Lengths - show details
-SW -SW Standard 3yr Warranty
At the time of purchase, the CR800 includes a standard warranty of 36 months. See our full warranty policy in the CR800/CR850 manual for the terms and conditions of this warranty.
-XW -XW 4yr Warr Extension
Our Extended Warranty adds 48 months to the standard 36-month warranty, bringing the total warranty period to 84 months. The extended warranty may be purchased only at the time of original product purchase. It may NOT be "added later." Except for the increased coverage length, the same terms and conditions apply to the extended warranty as apply to the standard warranty.
Calibration Certificate - show details
-NC -NC No Calibration Cert
The CR800 is shipped without a calibration certificate.
-CC -CC Calibration Cert
When this option is chosen, a two-page calibration certificate is shipped with the data logger.

Add to your Quote List


Product Details
Typically Ships Within 14 - 21 Days
Restockable Yes
Warranty 3 years
Compliance CE Compliance Image RoHS Compliance Image

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.

Ships With
(4) 505 Screw #6-32 x .375 Pan Phillips
(1) 8125 Flat-Bladed Screwdriver, 2.5 mm Blade x 50 mm Shaft
(4) 6044 Grommet for #6 or 8 Screw
(1) 10873 Serial Data Cable, 9-Pin Female to 9-Pin Male
(1) 18633 Default Datalogger Program
(1) 3315 Type T Thermocouple

Common Accessories

CR1000KD
 
The CR1000KD is a portable keyboard display for viewing and entering data logger data. One CR1000KD may be carried from station to station in a CR800 network. Users can customize menus and displays, simplifying routine operations.
CD100
 
The CD100 can be mounted in an enclosure lid allowing the user to enter and display data without opening the enclosure. It has a vacuum florescent display for responsive use through a very wide operating temperature range. The user can customized menus and displays, simplifying routine operations.
SC32B
 
This Optically Isolated Interface is used to attach an AC-powered PC with the CR800. The SC32B includes a cable for connecting with the data logger's CS I/O port, and includes another cable for connecting with the PC's 9-pin serial port. Customers who want to connect with the PC's USB port instead of the 9-pin serial port should use the SC-USB interface.
17394
 
The 17394 interface cable provides a USB connector on one end and a 9-pin male RS-232 connector on the other end. The USB connector attaches to the USB port on a PC, and the RS-232 connector attaches to the RS-232 port on the CR800. Cable length is 6 feet (2 m).
SC110
 
The SC110 consists of two cables, each 2 feet (0.6 m) in length. By having two cables, connection of either an RS-232 DCE or DTE device is supported, depending on the cable used.
SC-CPI
 
SC-CPI Datalogger Serial to CPI Interface
 
The SC-CPI allows the CR800 to communicate with a CDM.
Temperature Ranges
-ST -ST -25 to +50C
-XT -XT -55 to +85C
Warranty Lengths - show details
-SW -SW Standard 1yr Warranty
At the time of purchase, the SC-CPI includes a standard warranty of 12 months. See our full warranty policy in the SC-CP manual for the terms and conditions of this warranty.
-XW -XW 4yr Warr Extension
Our extended warranty adds 48 months to the standard 12 month warranty, bringing the total warranty period to 60 months. The extended warranty may be purchased only at the time of original product purchase. It may NOT be "added later." Except for the increased coverage length, the same terms and conditions apply to the extended warranty as apply to the standard warranty.

Other Accessories

 
The 18634 is offered for customers who want a paper CR800/CR850 Operator's Manual in a 3-ring binder.
27373
 
The 27373 facilitates connecting multiple wires into the same terminal, such as for SDI-12.

Replacement Parts

3768
 
The 3768 is shipped attached to the CR800. This green, plug-in power connector provides screw terminals for connecting the 12 V and GND wires of the data logger's power supply. The 3768 may be purchased to replace a lost or damaged power connector.
13519
 
The 13519 lithium battery powers the clock and SRAM when the primary 12 Vdc power supply is not connected.
10645
 
The 10645 is the screw used in the ground lug.
6554
 
The 6554 Single 0.16-Unit Silica Desiccant Bag desiccates the inside of the CR800. Campbell Scientific suggests replacing this desiccant when the lithium battery is replaced.
 
The 18624 orders a two-page calibration certificate.
505
 
These screws, along with the 6044 grommets, are commonly used together to secure our equipment to the backplates of our enclosures.
6044
 
These grommets are commonly used with the 505 screws to secure our equipment to the backplates of our enclosures.
8125
 
The 8125 is a small, flat-bladed screwdriver that is extremely useful for opening the guillotine terminals on our data loggers and measurement control devices.
10873
 
The 10873 is a serial cable that is useful for connecting the RS-232 port of the data logger to the 9-pin RS-232 port of a computer. The cable is six feet long.
3315
 
This type T, 5 in. thermocouple is attached to a differential channel on several of our data logger wiring panels when the data logger is shipped. A 3315 may be ordered to replace a thermocouple that has become lost or damaged.

Services

 
The 18635 requires an RMA (Returned Material Authorization) from Campbell Scientific. When it is ordered, we will recalibrate a CR800 or CR850 to meet original specifications. Recalibration includes standard temperature testing (-25° to +50°C). Before and after calibration sheets are supplied with the data logger. The calibration price listed assumes return of a fully functional data logger; charges for all repairs will be added to the invoice.
 
This service is available only for individual units that have previously passed Extended Temperature Testing. The 18636 also requires concurrent purchase of recalibration. An RMA (Returned Material Authorization) from Campbell Scientific is required.
 
Every CR800 is tested and guaranteed to perform within published specifications over the standard temperature range. Units are tested to standard operating range unless extended testing (-55° to +85°C) is specified. For extended temperature range testing, analog accuracies are derated approximately two times over published specifications.
 
The 18624 orders the two-page calibration certificate for the CR800. Unless specified, the CR800 is shipped without a calibration certificate.
 
The 34154 provides factory recalibration of the CR800 or CR850 to meet original specifications, then sends the recalibrated data logger to be validated by a certifying body that is A2LA accredited to the ISO 17025 standards.

This service requires an RMA (Returned Material Authorization) from Campbell Scientific. The factory recalibration includes comprehensive testing of all data logger functions over its standard temperature range (-25° to +50°C) and the replacement of the internal lithium battery and desiccant packs. During testing, the data logger’s operating system is updated, and all settings are restored to factory defaults unless otherwise requested. Upon completion of the factory calibration, the data logger is sent to the A2LA accredited certifying body referenced above for calibration validation.