RETIRED ›
This product is no longer available and has been replaced by: CR1000. Some accessories, replacement parts, or services may still be available.
Product Details
Typically Ships Within 21 - 28 Days
Restockable Yes
Warranty
Compliance CE Compliance Image

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.


Other Accessories

CR10XTCR
 
The CR10XTCR provides a temperature reference for thermocouple measurement. Its leads connect directly to channels 1H, E3, and AG on the CR10X Wiring Panel. The thermistor and resistors are attached to a small printed circuit board [#8289]. The aluminum thermocouple cover [#10630] reduces thermal gradients across the analog inputs.
 
The 17154 provides the CR10X Operator's Manual in paper form (bound in a 3-ring binder).

Replacement Parts

CR10XWP
 
This black, anodized aluminum wiring panel has a label with "CR10X" written in white. The CR10XWP include a switched 12 V terminal, redistributed analog grounds (dispersed among analog channels rather than grouped), unpluggable terminal block for 12 V connections, gas-tube spark gaps, and 12 V supply on pin 8 to power our COM-series phone modems and other peripherals.
3768
 
This green, plug-in power connector is shipped attached to the CR10X-2M datalogger. The connector provides screw terminals for connecting the 12 V and GND wires of the dataloggger's power supply.
4107
 
The 4107 base plate is a component of the CR10XWP Wiring Panel. It is listed here in the event that some mishaps should befall the original base plate and a replacement is needed.
6554
 
The 6554 Single 0.16-Unit Silica Desiccant bag desiccates the inside of the CR10X-2M. It is often replaced when the lithium battery is replaced.
8025
 
This 3 V lithium battery maintains power to volatile areas of CR10X-2M memory (e.g., clock) when the main power supply is disconnected or turned off. The 8025 should be periodically replaced.
8299
 
The 8299 provides only the reference junction component of the CR10XTCR; the CR10XTCR includes both the the 8299 thermistor and an aluminum cover.
10630
 
The 10630 aluminum thermocouple cover is available as a replacement part for existing CR10(X) customers. The cover reduces thermal gradients across the analog inputs for thermocouple measurement.
3315
 
This type T thermocouple is attached to a differential channel on the CR10X-2M. The programming examples in the Overview Section of the datalogger manual use the 3315.
1113
 
The 1113 is used to attach sensor leads to screw terminals.

Services

15843
 
Retesting is available only for individual units that have previously passed Extended Temperature Testing. Retesting also requires concurrent purchase of recalibration, in this case, the 16542. An RMA (Returned Material Authorization) from Campbell Scientific is required.
 
Individual dataloggers can also be returned to Campbell Scientific on an RMA to determine if they can pass Extended Temperature Testing. Extended temperature testing of a previously purchased unit also requires purchase of recalibration.
 
The 16542 requires an RMA (Returned Material Authorization) from Campbell Scientific. When ordered, the CR10X is recalibrated to meet original specifications. Before and after calibration sheets are supplied with the datalogger. The datalogger is recalibrated over the standard -25° to +50°C temperature range.
 
This service increases delivery time by approximately one week. The 21852 is offered for customers who require calibration validation from an accredited calibration laboratory. When the 21852 is ordered, Campbell Scientific calibrates the datalogger, and then sends the datalogger to Simco Electronics in Salt Lake City, Utah. After Simco receives the datalogger, they perform a calibration validation under the A2LA/NVLAP accreditation. Simco also provides a calibration certificate.