MetSens300

MetSensCBL1

MetSens SDI-12 Replacement Cable

MetSensCBL2

MetSens RS-485 Replacement Cable

MetSensCBL3

MetSens RS-232 Replacement Cable

34344

MetSens or WINDSONIC Stand Mount

17387

ClimaVue, MetSens or WindSonic Mounting Pipe Kit

31897

RJ45 Pin (Male) to Terminal Dongle Data Cable

33815

SDI-12 Terminal Bus Kit

39120

DIN Rail Terminal Kit with 2 Terminals and 5 Wires

39642

SDI-12 DIN Rail Terminal Bus Kit without Mounting Bracket

39643

RS-485 DIN Rail Terminal Bus Kit without Mounting Bracket

MetSensCBL1

MetSens SDI-12 Replacement Cable

This cable connects a MetSens compact weather sensor with SDI-12 output to the datalogger. The MetSensCBL1 consists of a 22 AWG cable with a pinned military-style connector and high-temperature, high-voltage, UV-resistant PVC insulation.

MetSensCBL2

MetSens RS-485 Replacement Cable

This cable connects a MetSens compact weather sensor with RS-485 Modbus output to the datalogger. The MetSensCBL2 consists of a 22 AWG cable with a pinned military-style connector and high-temperature, high-voltage, UV-resistant PVC insulation.

MetSensCBL3

MetSens RS-232 Replacement Cable

This cable connects a MetSens compact weather sensor with RS-232 output to the datalogger. The MetSensCBL3 consists of a 22 AWG cable with a pinned military-style connector and high-temperature, high-voltage, UV-resistant PVC insulation.

17387

ClimaVue, MetSens or WindSonic Mounting Pipe Kit

One mounting kit is needed per sensor. This mount includes a 17386 Mounting Tube, a right-angle bracket, two U-bolts, and four nuts.

34344

MetSens or WINDSONIC Stand Mount

The 34344 is a mounting kit for the MetSens series of compact weather sensors. The kit can be installed on a vertical pipe or mast, or on a horizontal crossarm less than 6.35 cm (2.5 in.) in diameter. The kit includes a mounting stand and three pan truss screws, which are used to attach the following: the MetSens sensor; two 5/16 x 3.0 in. carriage screws; and two sets of wing nuts, washers, and lock washers.

39120

DIN Rail Terminal Kit with 2 Terminals and 5 Wires

The 39120 provides the needed DIN rail terminals, separator, and wires to connect any product to a data logger or other peripheral that requires five wires for connection. This kit provides the following wires: black, green, red, white, and clear. The color-coding of these wires matches the wire coloring of the product for ease in connection, maintenance, and troubleshooting.

39642

SDI-12 DIN Rail Terminal Bus Kit without Mounting Bracket

The 39642 makes it easier for you to connect wires from multiple SDI-12 sensors into one set of terminals on a data logger. The 39642 uses six DIN-rail mountable (pn 27479), 6-wire terminal blocks. The 39642 is a jumper that electrically connects two terminal blocks together at a time (pn 32918). This setup allows up to 11 SDI-12 sensors to be connected to one set of terminals on a data logger.

39643

RS-485 DIN Rail Terminal Bus Kit without Mounting Bracket

The 39643 makes it easier for you to connect wires from multiple RS-485 sensors into one set of terminals on a data logger. The 39643 uses six DIN-rail mountable (pn 27479), 6-wire terminal blocks. The 39643 is a jumper that electrically connects two terminal blocks together at a time (pn 32918). This setup allows up to 17 RS-485 sensors to be connected to one set of terminals on a data logger.

31897

RJ45 Pin (Male) to Terminal Dongle Data Cable

The 31897 can be plugged into the RJ45 RS-232 port on a CR6 or CR1000X datalogger to connect the datalogger to an RS-232 sensor.

33815

SDI-12 Terminal Bus Kit

The 33815 makes it easier for you to connect wires from multiple SDI-12 sensors into one set of terminals on a data logger. The 33815 uses six DIN-rail mountable (pn 27479) 6-wire terminal blocks. The 33815 jumpers two connectors together at a time (pn 32918). This setup allows up to 11 SDI-12 sensors to be connected to one set of terminals on a data logger.