WINDSONIC4-L
 
WINDSONIC4-L Gill 2-D Sonic Wind Sensor w/SDI-12 Output
 
WINDSONIC4-L Options - show details
-L ft cable per sensor

Allowed values: 0-300 ft, increments of 1 ft

Maximum Cable Length:
  • 300 ft (SDI-12 output with one sensor connected to a single port)
  • 200 ft (SDI-12 output with two to ten sensors connected to a single port)
Contact Campbell Scientific if longer cable lengths are required.

Campbell Scientific recommends the following cable lengths assuming the sensor is mounted atop the tripod/tower via CM202 crossarm:
  • 13 ft (WINDSONIC4-L13) for a CM106B tripod, CM110 tripod, or UT10 tower
  • 19 th (WINDSONIC4-L19) for our CM115 tripod
  • 24 ft (WINDSONIC4-L24) for our CM120 tripod or UT20 tower
  • 34 ft (WINDSONIC4-L34) for our UT30 tower
Cable Termination Options - show details
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a prewired enclosure.
-C -C w/ET/CS110 Connector
-RQ -RQ w/RAWS Connector

Add to your Quote List


Product Details
Restockable Yes
Warranty 1 year
Compliance CE Compliance Image
Ships With
(1) 17387 ClimaVUE50, MetSENS or WindSonic Mounting Pipe Kit
(1) CD from original mfg

Other Accessories

34344
 
The 34344 is a mounting kit that can be installed on a vertical pipe or mast, or on a horizontal crossarm less than 6.35 cm (2.5 in.) in diameter. The kit includes a mounting stand and three pan truss screws, which are used to attach the following: the sensor; two 5/16 x 3.0 in. carriage screws; and two sets of wing nuts, washers, and lock washers.
33815
 
The 33815 makes it easier for you to connect wires from multiple SDI-12 sensors into one set of terminals on a data logger. The 33815 uses six DIN-rail mountable (pn 27479) 6-wire terminal blocks. The 33815 jumpers two connectors together at a time (pn 32918). This setup allows up to 11 SDI-12 sensors to be connected to one set of terminals on a data logger.

Replacement Parts

 
WINDSONIC4CBL-L Windsonic Replacement SDI-12 Signal/Power Cable
 
The WINDSONIC4CBL-L connects the WindSonic4 to the datalogger. It consists of a 22 AWG cable with a pinned military-style connector, and a UV-resistant Santoprene jacket. Maximum cable length is 200 feet.
WINDSONIC4CBL Options - show details
-L ft per sensor cable

Allowed values: 1-300 ft, increments of 1 ft

Maximum Cable Length:
  • 300 ft (SDI-12 output with one sensor connected to a single port)
  • 200 ft (SDI-12 output with two to ten sensors connected to a single port)
Contact Campbell Scientific if longer cable lengths are required.

Campbell Scientific recommends the following cable lengths assuming the sensor is mounted atop the tripod/tower via CM202 crossarm:
  • 13 ft (WINDSONIC4CBL-L13) for a CM106B tripod, CM110 tripod, or UT10 tower
  • 19 ft (WINDSONIC4CBL-L19) for our CM115 tripod
  • 24 ft (WINDSONIC4CBL-L24) for our CM120 tripod or UT20 tower
  • 34 ft (WINDSONIC4CBL-L34) for our UT30 tower
Cable Termination Options - show details
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a prewired enclosure.
-C -C w/ET/CS110 Connector
-RQ -RQ w/RAWS Connector
17387
 
The 17387 includes a 17386 Mounting Tube, a CM220 right angle bracket, two U-bolts, and four nuts. It is used to attach a WindSonic4 to a tripod or tower via a CM202, CM204, or CM206 crossarm.