VU01-L
 
VU01-L Hukseflux Ventilation Unit for SR20
 
VU01-L Options - show details
-L ft cable per sensor

Allowed values: 0-17 ft, increments of 1 ft

Cable Termination Options
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector

Add to your Quote List


Product Details
Restockable Yes
Warranty 1 year
Compliance CE Compliance Image RoHS Compliance Image
Ships With
(2) 25866 M5 x 30 mm Stainless-Steel Screw Cap Hex Socket
(2) M5 Retaining Torque Nuts from original mfg
(4) 5 mm Washers from original mfg
(1) Torx Key T25 from original mfg
(1) Spare Filter from original mfg
(1) Product Certificate

Common Accessories

CM261
 
CM261 Single-Axis Tracker Mounting Stand
 
The CM261 single-axis tracker pyranometer mount with adjustable plane simplifies the mounting of any pyranometer, ventilation unit, reference cell, or SPN1 to hexagonal, round, and square single-axis torque tubes. The CM261 is a combination and simplification of the CM260 and CM265 to make ordering easier and usability friendlier. The bracket includes provisions for mounting the sensors and ventilation units at different heights, allowing the sensing element to be mounted at the same height as the solar modules.
Mounting Plate Options - show details
-SP -SP w/Small Mount Plate
This mounting plate option is compatible with the following: MS-40/60/80, MS-40M/60M/80M, SR30, SR05, SR11, SR15, SR20-T2, SR20-D2, SP Lite 2, CMP3/6/10/11/21/22, SMP3/6/10/11/21/22, CGR3/4, and SGR3/4.
-LP -LP w/Large Mount Plate
This mounting plate option is compatible with the following: SPN1, PSP, GPP, SPP, and Si-01TC Reference Cell (CS325DM).
-VN -VN w/VU01 or MV-01 Plate
This mounting plate option is compatible with the following: VU01 and MV-01.
-CV -CV w/CVF4 Plate
This mounting plate option is compatible with the following: CVF4.
Torque Tube Mounting - show details
-AT -AT for ATI Torque Tube
This torque tube mounting option is compatible with hexagonal torque tubes such as ATI.
-NT -NT for NexTracker T Tube
This torque tube mounting option is compatible with round torque tubes such as NexTracker.
-GT -GT for Generic T Tube
This torque tube mounting option is compatible with square torque tubes.

Other Accessories

CM220
 
Using a VU01 mounting stand, the VU01-L can be fastened to a CM220 Right-Angle Mounting Bracket. The CM220 can then be attached to a mast or a crossarm.
17953
 
Using a VU01 mounting stand, the VU01-L can be fastened to a 17953 1- x 1-inch Nu-Rail Crossover Fitting. The 17953 can then be attached to a mast or crossarm.
CMB200
 
The CMB200 Crossarm Brace Kit is designed to provide additional stability when using a crossarm mounted on Campbell Scientific tripods and towers. This kit provides support for crossarms with heavier or sensitive sensor loads, as well as added stability in higher winds. Each kit includes one brace arm and three sets of mounting brackets.

Replacement Parts

 
VU01CBL-L VU01 Replacement Cable
 
The VU01CBL-L replacement cable uses pn 8865 cable, which features 24 AWG cable with one-twisted pair and seven conductors shielded with a drain and Santoprene jacket.
VU01CBL-L Options - show details
-L ft cable per sensor

Allowed values: 1-17 ft, increments of 1 ft

Cable Termination Options
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
 
The 25866 may be purchased to replace a lost or damaged socket.
 
Initially, the VU01-L ships with a set of five replacement filters. The 31435 package contains five additional replacement filters.