T107
 
T107 T.Weather Toro ET Station, 3M
 
Charging Sources - show details
-NC -NC No Charging Source
This option is for customers who wish to supply their own customized charging source.
-AC -AC AC Power Kit
The 110 Vac to 16 Vac Transformer Kit float charges the system's sealed rechargeable battery. It requires 110 Vac power to be available and properly installed at the site.
-SP -SP 10W Solar Panel
This 10 W Solar Panel float charges the station's internal rechargeable battery. The solar panel's cable terminates in a connector that plugs into the outside of the enclosure. Cable length is 46 inches.
Communications - show details
-NM -NM No Modem
Select this option if you wish to provide your own communications modem at the weather station.
-SH -SH Short Haul Modem Kit
The Short-Haul Modem Package supports local communication between the T107 and a computer RS-232 serial port. The kit includes two RAD modems, a 10596 interface, a surge protector for the computer, a cable burial splice kit, and three cables. One 20 ft cable connects one RAD to the T107. (The T107 is surge protected by the connector board). A second cable, with an inline surge protector, connects the second RAD to a computer. The third cable is a straight-through 9-25 pin serial cable.
-PH -PH Phone Modem Kit
Choose this to have the T107 communicate with a computer equipped with a Hayes-compatible modem using a public switched telephone network. The kit includes a COM220 telephone modem, a 20 ft cable allowing attachment to the enclosure, burial splice kit for attachment to a phone line, and a patch cord to connect the COM220 to the RJ11C telephone jack. Surge protection is built into the T107 board. The COM220 is programmed for use in the US or Canada. Refer to the 19154 other accessory if you are in the UK.
Wind Sensor Options - show details
-NW -NW No Wind Sensor
Select this option if you do not want to measure wind speed and direction or you want to use your own wind sensor.
-MW -MW Met One 034B-ETM Wind
The 034B wind set combines a 3-cup anemometer and vane into a single integrated package. The cable terminates in a connector and is the ideal length for attachment to the T107 ETo Weather Station. Mount for attaching the sensor to the T107 is included.
-GW -GW Gill WindSonic1-ETM
The WindSonic1 does not have moving parts, which minimizes routine maintenance. It outputs an RS-232 signal that the T107's on-board CR1000 can measure. The cable terminates in a connector and is the ideal length for attachment to the T107 ETo Weather Station. Mount for attaching the sensor to the T107 is included.

Add to your Quote List


Product Details
Typically Ships Within 14 - 21 Days
Restockable Yes
Warranty 1 year
Compliance CE Compliance Image

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.

Ships With
(1) 10581 ET Station Shipping Kit, Default Version
(1) 10489 3 m White Aluminum Pole for ET Station (in two pieces)

Other Accessories

 
The 19154 is intended for customers who have chosen communication option "-PH" and their station will reside in the United Kingdom. When the 19154 is chosen, Campbell Scientific will program the COM220 Phone Modem for use in the UK.
 
The 16902 includes a pair of RF401 spread spectrum radios, an antenna cable, an antenna mounting bracket, a data cable, an ac transformer, and the 15970 dipole antenna. The RF401 operates in the 910 to 918 MHz frequency range, which is allocated in the US and Canada. You must order the field site antenna (17548, 14203, or 14205).
17548
 
The 17548 is a common accessory for the 16902 and 17546 spread spectrum kits. This 0 dBd, unity gain antenna is suitable for short, direct line-of-sight transmission. The antenna should reside inside the enclosure.
14203
 
This common accessory for the 16902 and 17546 spread spectrum kits is a 3 dBd, omnidirectional antenna suitable for the outdoors. The 14203 can be used at the base station or where you need to communicate with multiple stations located in different directions. This antenna is also preferred in applications in which the best radio path is not constant, including close-up applications without clear line-of-sight.
14205
 
The 14205, another common accessory for the 16902 and 17546 kits, provides a high-gain (6 dBd), directional (Yagi) antenna. Used outdoors, the 14205 has a narrow beam width that requires precise aiming. Its higher gain makes it useful for communicating over longer distances.
 
The 17547 includes a pair of RF416 spread spectrum radios, an antenna cable, an antenna mounting bracket, a data cable, an ac transformer, and the 17480 dipole antenna. The RF416 is a 50 mW spread spectrum radio that operates in the 2.45 to 2.46 GHz frequency range, which is allocated in many countries world-wide. You must order the field site antenna (16755).
16755
 
This common accessory for the 17547 provides a high-gain (13 dBd), directional (Yagi) antenna, suitable for outdoor use. A narrow beam width requires precise aiming. It is useful for longer distances, and when only communicating to one other station.
29354
 
The 29354 is a wireless networking peripheral that provides Wi-Fi connectivity over standard 802.11b/g/n networks. It is a low-power device that offers unique and powerful PakBus networking capabilities, but it is easy to configure.
 
The 32453 kit is used with our ET stations to provide license-fee 868 Mhz wireless serial communications in Europe. The RF422 radio included in the radio kit transmits data at 10 kbps with a maximum power of 25 mW. The radio employs listen-before-talk (LBT) and adaptive-frequency-agility (AFA) to provide a robust link of up to 5 km (line-of-sight). The RF422 supports point-to-point and point-to-multipoint datalogger communications.

Replacement Parts

 
The 19441 may be purchased to replace the CR1000M module that was originally contained in the T107. The CR1000M provides sensor measurement, timekeeping, data reduction, data/program storage and control functions. It has 4 MB of memory for data and program storage.
10070
 
The 10070 Enclosure RH Sensor measures the relative humidity inside of the enclosure. This measurement helps the customer know when the the desiccant needs to be replaced.
6182
 
The 6182 consists of a 7A h sealed rechargeable battery, leads, and a connector.
HMP60-ETS
 
The HMP60-ETS is the replacement temperature and relative humidity sensor for newer T107 stations. The HMP60-ETS includes an adapter that allows the sensor to fit in a MetSpec radiation shield. The MetSpec radiation shield has wingnuts on the bottom of the shield. If there are no wingnuts, the appropriate replacement sensor for your T107 station is the HMP60-ETR (see below).
HMP60-ET
 
The HMP60-ET is the replacement temperature and RH sensor for older ET stations. The sensor's cable terminates in a connector and is the ideal length for attachment to the ET107 or ET106 ETo Weather Station.
CS305-ETM
 
The CS305-ETM is the pyranometer and leveling mount included with the T107. The pyranometer is fitted with a 40" cable that terminates in a connector for attachment to the T107. The CS305-ETM measures total sun and sky solar radiation using a silicon photocell.
TE525-ET
 
The TE525-ET is the tipping bucket raingage included with the T107. It has a 6" orifice and a 55" cable that terminates in a connector for attachment to the T107. The TE525-ET measures in 0.01" increments.
034B-ETM
 
The 034B-ETM is the wind set and mount included with the T107 when option -MW is chosen. This wind set combines a 3-cup anemometer and vane into a single integrated package. Its cable terminates in a connector and is the ideal length for attachment to the T107 ETo Weather Station.
WINDSONIC1-ETM
 
The WindSonic1-ETM is the ultrasonic anemometer and mount included with the T107 when option -GW is chosen. This anemometer does not have moving parts, which minimizes routine maintenance. It outputs an RS-232 signal that the T107's on-board CR1000 can measure. The cable terminates in a connector and is the ideal length for attachment to the T107.
10589
 
The 10589 provides the short haul modem kit included with the T107 when option -SH is chosen. It enables local communication between the T107 and a computer RS-232 serial port. The kit consists of two RAD modems, a 10596 interface, a surge protector for the computer, a cable burial splice kit, and three cables.
10585
 
The 10585 provides the phone modem kit included with the T107 when option -PH is chosen. It enables communication between the station and a computer equipped with a Hayes-compatible modem over a public switched telephone network. The kit consists of a COM220 telephone modem, a 20-ft cable allowing attachment to the enclosure, burial splice kit for attachment to a phone line, and a patch cord to connect the COM220 to the RJ11C telephone jack. The COM220 is programmed for use in the US or Canada. Refer to the 19154 other accessory if you are in the UK.
CS305-ET
 
The CS305-ET provides the T107's pyranometer but not the leveling mount.
034B-ET
 
The 034B-ET provides the wind set but not the mount.
WINDSONIC1-ET
 
The WindSonic1-ET provides the ultrasonic anemometer but not the mount.
 
The 10489 consists of two pieces of aluminum pipe that provides a total length of 8' 9". It is painted white.
 
The 10581 is the default shipping kit for our ET stations. It consists of various hardware, cable ties, desiccant, and the components used to ground the station.

Services

 
The 19387 kit converts a T.Weather 106 station (a variant of the ET106 station) to a T107 station (a variant of the ET107 station).