SR50ATH-L
 
SR50ATH-L CSC Sonic Ranging Sensor w/Heater & Temp Sensor
 
SR50ATH-L Options - show details
-L ft cable per sensor

Allowed values: 0-1000 ft, increments of 1 ft

-LH ft cable per heater

Allowed values: 0-200 ft, increments of 1 ft

Cable Termination Options - show details
-PT -PT w/Tinned Wires
Both the sensor cable and the heater cable terminate in pigtails that connect directly to the datalogger. The heater cable attaches to a switched 12 Vdc source.
-PW -PW w/Pre-Wire Connector

Add to your Quote List


Product Details
Typically Ships Within 35 - 42 Days
Restockable Yes
Warranty 2 years
Compliance CE Compliance Image RoHS Compliance Image

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.

Ships With
(1) Test Report
(1) SR50ATCBL-L Replacement SR50AT Cable

Common Accessories

19517
 
This mounting kit attaches directly to a CM206 crossarm or user-supplied pole with a 1-in. to 1.75-in. outside diameter.
19484
 
This mounting stem attaches to a sensor. The stem is then attached to the CM206 crossarm or a user-supplied pole via a CM220 mount, 17953 Nu-Rail fitting, or CM230 Adjustable Inclination Mount.
17953
 
The 17953 connects a vertical 1-inch pipe to a horizontal 1-inch pipe. The 17953 is typically used to attach a sensor with a 1-inch vertical pipe mount to a CM202, CM204, or CM206 crossarm. This usage provides functionality similar to the CM220 right-angle mounting bracket.
CM220
 
The CM220 right-angle mounting bracket can attach a sensor with a vertical pipe mount (e.g., most wind sensors) to a crossarm. It is compatible with pipes that have a 1- to 1.5-inch outer diameter.
CM230
 
The CM230 is an adjustable mount to point directional antennas or sensors at a specific target. The inclination can be adjusted to any angle from horizontal to vertical, supporting the use of upward-directed antennas or downward-directed infrared thermometers or snow-depth sensors.
CM230XL
 
The CM230XL is an adjustable mount to point directional antennas or sensors at a specific target. The inclination can be adjusted to any angle from horizontal to vertical, supporting the use of upward-directed antennas or downward-directed infrared thermometers or snow-depth sensors.
41303-5A
 
The 41303-5A is a naturally aspirated, 6-plate radiation shield. Its louvered construction allows air to pass freely through the shield, serving to keep the probe at or near ambient temperature. The shield's white color reflects solar radiation.
RAD06
 
The RAD06 uses a double-louvered design that offers improved sensor protection from driving rain, snow, and insect intrusion. It also has lower self-heating in bright sunlight combined with higher temperatures (> 24°C (~75°F)) and low wind speeds (< 2m/s (~4.5 mph)), providing a better measurement.

Replacement Parts

SR50ATCBL-L
 
SR50ATCBL-L Replacement SR50AT Cable
 
Note: This heater cable is only replaceable via a Returned Material Authorization (RMA).
SR50ATCBL-L Options - show details
-L ft per sensor cable

Allowed values: 1-1000 ft, increments of 1 ft

Cable Termination Options
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
-C -C w/ET/CS110 Connector
905
 
Two bags of the 905 desiccant are used inside the electronics housing. The 905 desiccant is not replaced when the transducer is replaced.
4091
 
Six bags of the 4091 desiccant are used to dry the air in the area above the transducer. Six bags are included in the transducer replacement kit.
32571
 
The 32571 includes a transducer housing, desiccant, and a replacement O-ring. It is recommended that the transducer housing assembly be replaced every three years, or annually in high-humidity environments.

Services

 
The 30249 is a service for the SR50A provided at the factory. All factory replacements require an RMA (Returned Material Authorization).