RAWS-P
RAWS-P-NC-NM-7-MM
 
RAWS-P Remote Automated Weather Station, Permanent
 
Calibration Certificate - show details
-NC -NC No Calibration Cert
Unless specified, the RAWS-P is shipped without a calibration certificate.
-CC -CC CR1000M Calib Cert
If specified, the RAWS-P is shipped with a two-page calibration certificate.
Communication Options - show details
-NM -NM No Communications
Select this option for a user-supplied communication method.
Rechargeable Batteries - show details
-7 -7 7Ah Batt & CH150
The -7 option provides a 12-Vdc, 7-Ahr sealed rechargeable battery and a CH150 regulator. A charging source is not included (see Common Accessories for compatible solar panels and wall charger).
-24 -24 24Ah Batt & CH150
The -24 option provides a 12-Vdc, 24-Ahr sealed rechargeable battery and a CH150 regulator. A charging source is not included (see Common Accessories for compatible solar panels and wall charger).
Enclosure Mounts - show details
-MM -MM Tripod Mast Mounting
Order the "-MM" option if you want to mount your RAWS-P to a tripod mast or a user-supplied pole with a 1.25" to 2.1" OD. A three-piece bracket attaches to the top of the enclosure and an identical three-piece bracket attaches to the bottom of the enclosure. Each bracket mounts to the mast or pole via a u-bolt.
-TM -TM Tower Mounting
Order the "-TM" option if you want to mount your RAWS-P to two legs on a UT10, UT20, or UT30 tower. This mounting bracket option uses the same 3-piece brackets as the "-MM" option, except the pieces are rearranged so that the flanges are on the side of the bracket instead of in the middle. Four u-bolts mount the brackets to the tower legs.

Please note that enclosures with the "-TM" option are shipped configured for the UT10 tower. UT20 and UT30 customers will need to: (1) remove the bolts attaching the bracket to the enclosure, (2) slide out the flange sections so that the distance between the center of each flange is 17", and (3) reattach the bracket to the enclosure using the original bolts.
How to Order

Add to your Quote List


Product Details
Typically Ships Within 45 - 52 Days
Restockable Yes
Warranty 1 year
Compliance –

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.

Ships With
(1) CR1000KD Keyboard/Display for the CR1000, CR800, or CR6
(1) 1113 Flat-Bladed Screwdriver, 3.0 mm Blade x 60 mm Shaft
(1) 7363 Enclosure Supply Kit, Standard Size
(1) 7364 UV-Resistant 8 in. Cable Ties (quantity of 12)
(1) 10873 Serial Data Cable, 9-Pin Female to 9-Pin Male
(1) — Conduit kit
(1) 18903 #2 Phillips Screwdriver with 8 in. Blade
(1) 6186 External Battery Cable for CH150, CH200, PS150, or PS200

Common Accessories

16138 CR1000M Tested to Extended Temp (-55 to +85C)
 
The CR1000M inside of the RAWS-P may be temperature tested for the -55° to +85°C range. For this temperature range, analog accuracies are derated approximately two times over published specifications.
18897
18897 Wall Charger 24Vdc 1.67A Output, 110-240Vac 1A Input, for RAWS Stations, 6ft Cable
 
The 18897 wall charger allows you to float-charge the sealed rechargeable battery via ac power. The 18897outputs 24 Vdc @ 1.67 A and accepts 100 to 240 Vac.
SP10-LQ
SP10-LQ
 
SP10-LQ 10W Solar Panel for RAWS Station
 
The SP10-LQ solar panel provides a 10 W maximum peak power, 9 W guaranteed minimum power, 0.59 A current at peak, and 16.8 V voltage at peak. It's cable terminates in a military-style connector that attaches to the RAWS-P connector panel.
Cable Length - show details
-LQ ft cable per SP10-LQ

Allowed values: 1-1000 ft, increments of 1 ft

Recommended lead length is 15 ft.
SP20-LQ
SP20-LQ
 
SP20-LQ 20W Solar Panel for RAWS Station
 
The SP20-LQ solar panel provides a 20 W maximum peak power, 18 W guaranteed minimum peak power, 1.19 A current at peak, and 16.8 V voltage at peak. It's cable terminates in a military-style connector that attaches to the RAWS-P connector panel.
Cable Length - show details
-LQ ft cable per SP20-LQ

Allowed values: 1-1000 ft, increments of 1 ft

Recommended cable length is 15 ft.

Other Accessories

CS516-LQ
CS516-LQ
 
CS516-LQ Fuel Moisture & Temperature Sensor w/Fuel Sticks for RAWS Station
 
The CS516-LQ consists of a CS506 Fuel Moisture Probe, a 26601 10-hour Fuel Moisture Stick, a CS205 Fuel Temperature Stick, and a 107 Thermistor mounted on a 26817 Mounting Stake. The cables on the CS506 and 107 probes have a user-specified length and terminate in a military style connector instead of pigtails. The connector attaches to the RAWS-P Fire Weather Quick Deployment Station.
Cable Lengths - show details
-LQ ft cable per moisture

Allowed values: 1-1000 ft, increments of 1 ft
-LT ft cable per temp

Allowed values: 1-2500 ft, increments of 1 ft
25316
25316 GOES 11dBi Yagi RHCP Antenna w/Mounting Hardware
 
The 25316 is used with the TX320, TX312, and OMNISAT-M satellite transmitters. A COAXNTN-L cable is required to attach the antenna to the satellite transmitter.
COAXNTN-L
COAXNTN-L
 
COAXNTN-L Antenna Cable RG8 w/2 Type N Male Connectors
 
The COAXNTN-L consists of an RG8/U, low-loss coaxial cable fitted with a type N male connector on each end.
Cable Length - show details
-L ft per antenna cable

Allowed values: 1-500 ft, increments of 1 ft

Recommended length is 15, 25, or 35 ft (4.6, 7.7, or 10.8 m).
17992
17992 28dBi GPS Antenna 3.3V Jam- Resistant Active w/o Cable
 
The 17992 is used with the TX320 and TX312 GOES satellite transmitters. It attaches to the transmitter via the 18017-L cable.
18017-L
18017-L
 
18017-L GPS Antenna Cable
 
The 18017-L connects the 17992 GPS Antenna to GPS receiver with a SMA female connector.
Cable Length - show details
-L ft per cable

Allowed values: 1-200 ft, increments of 1 ft

Replacement Parts

18411
18411 Sub RAWS Connector Panel
 
The 18411 connector panel is included with the RAWS-P and is available as a replacement item. It has color-coded, keyed connectors for attaching the sensors.
18928 RAWS Replacement 7Ah Sealed Rechargeable Battery
 
The 18928 battery is a component of the -7 Rechargeable Battery Option. This 7-Ahr sealed rechargeable battery is available as a replacement item.
10075
10075 BP24 24Ah 12V Sealed Rechargeable Battery w/o Mounting Hardware
 
The 10075 battery is a component of the -24 Rechargeable Battery Option. This 24-Ahr sealed rechargable battery is available as a replacement item.
CR1000M
CR1000M-ST-SW-NC
 
CR1000M Measurement & Control Module w/o Wiring Panel
 
The CR1000M may be purchased to replace a module that has been lost or damaged. It provides sensor measurement, timekeeping, data reduction, data/program storage and control functions. The CR1000M has 2 Mbytes of memory for data and program storage.
Temperature Ranges - show details
-ST -ST -25 to +50C
Every CR1000M is tested and guaranteed to perform within published specifications over the standard temperature range. Units are tested and shipped to standard operating range unless extended testing is specified.
-XT -XT -55 to +85C
For extended temperature range testing, analog accuracies are derated approximately two times over published specifications. Extended testing covers the -55° to +85°C range. Batteries are not temperature tested.
Warranty Lengths - show details
-SW -SW Standard 3yr Warranty
At the time of purchase, the CR1000M includes a standard warranty of 36 months. See our full warranty policy in the CR1000 manual for the terms and conditions of this warranty.
-XW -XW 4yr Warr Extension
Our Extended Warranty adds 48 months to the standard 36 month warranty, bringing the total warranty period to 84 months. The extended warranty may be purchased only at the time of original product purchase. It may NOT be "added later." Except for the increased coverage length, the same terms and conditions apply to the extended warranty as apply to the standard warranty.
Calibration Certificate - show details
-NC -NC No Calibration Cert
The CR1000M is shipped without a calibration certificate.
-CC -CC Calibration Cert
If specified, the CR1000M is shipped with a two-page calibration certificate.
10873
10873 9-Pin Female to 9-Pin Male Serial Data Cable, 6ft
 
This replacement cable has a 6 foot length. The 10873 terminates in a 9-pin female connector on one end and a 9-pin male connector on the other end. The female connector attaches to the RS-232 port on a PC, and the male connector attaches to the RAWS-P connector panel.
6650 14 AWG Enclosure Ground Wire w/Lug, 36 Inches
 
The 6650 consists of a 36-in. ground wire and lug connector. It may be purchased to replace a ground wire and lug connector that has been lost or damaged.
2207
2207 4 inch Nylon Cable Tie
 
Five of these 4-inch cable ties are included with the RAWS-P. The cable ties have a flexible, nylon construction, and are available as a replacement item.
2833 4 AWG Wire, THHN INS Copper Stranded
 
One foot of this 4-gauge copper wire is included with the RAWS-P. The copper wire connects the ground lug to the ground rod.
5449
5449 Enclosure Case Ground Lug Single Connector
 
The 5449 ground lug is attached to the RAWS-P enclosure. It may be purchased to replace a lost or damaged ground lug. A ground lug is required to properly ground the RAWS-P.
18744
18744 Plug 1.38 To 1.75 Holes Liquid Tight Kit Stahlin Hpseries 3
 
One plug that covers a 1.38" to 1.75" diameter hole is included with the RAWS-P. The 18744 may be purchased to replace a lost or damaged plug.
18377
18377 Plug 0.50 To 0.81 Holes Liquid Tight Kit Stahlin Hpseries 1
 
One plug that covers a 0.45" to 0.81" diameter hole is included with the RAWS-P. The 18377 may be purchased to replace a lost or damaged plug.
5252
5252 Circular Connector Mil Receptacle Dust Cap W/Chain MS3181-10N
 
Four of these dust caps are included with the RAWS-P. They cover the WS/WD, FM/FT, TEMP/RH, and SOLAR RAD sensor connectors. Individual dust caps may be purchased to replace a lost or damaged dust cap.
5010
5010 Circular Connector MilReceptacle Dust Cap W/Chain MS3181-8N
 
Three of these dust caps are included with the RAWS-P. The caps cover the PRECIP, SDI-12, and BATT CHARGER/SOLAR PANEL connectors. The 5010 may be purchased to replace a lost or damaged dust cap.
18397
18397 COAX SMA Connector Protective Cap W/Chain
 
This dust cap covers the GPS Antenna connector on the RAWS-P connector panel. The 18397 may be purchased to replace a lost or damaged dust cap.
18396
18396 Circular Connector N Type Protective Cap W/Chain
 
Two of these dust caps are included with the RAWS-P. The dust caps cover the RF OUTPUT and GOES ANTENNA connectors. The 18396 may be purchased to replace a lost or damaged dust cap.
18815
18815 Cable Tie 11 Inch Hook & Loop Nylon Black
 
Five 11" Hook and Loop Cable Ties are included with the RAWS-P. The 18815 is available as replacement items.
6186
6186 External Battery Cable for CH150, CH200, PS150, or PS200, 10 ft
 
This two-conductor cable has a two-pin connector on one end that attaches to the power supply, and pigtails on the other end that attach to the battery. The cable is 10 ft long.
7363
7363 Enclosure Supply Kit, Standard Size
 
The enclosure supply kit includes desiccant, a humidity indicator card, cable ties, wire tie tabs, putty for sealing the conduit, and screws and grommets for attaching peripherals to the enclosure backplate.
7364
7364 Cable Tie 8 inch UV Resistant Kit (Qty 12)
 
The kit includes 12 Tefzel® 8 in. cable ties (pn 7362) that are resistant to gamma radiation, UV radiation, and chemicals.
18903
18903 #2 Phillips Screwdriver, 8" Blade
 
One of these screwdrivers is shipped with a RAWS-P station. The 18903 may be purchased as a replacement part.
1113
1113 Flat-bladed Screwdriver, 3.0mm blade x 60mm shaft
 
The 1113 is used to attach sensor leads to screw terminals.