RETIRED ›
This product is no longer available and has been replaced by: PS150. Some accessories, replacement parts, or services may still be available.
PS100
 
PS100 12V Power Supply w/Charging Regulator & 7Ah Sealed Rechargeable Battery
 
Warranty Lengths - show details
-SW -SW Standard 1yr Warranty
At the time of purchase, the PS100 includes a standard warranty of 12 months. See our full warranty policy in the PS100/CH100 manual for the terms and conditions of this warranty.
-XW -XW 4yr Warr Extension
Our Extended Warranty adds 48 months to the standard 12 month warranty, bringing the total warranty period to 60 months. The extended warranty may be purchased only at the time of original product purchase. It may NOT be "added later." Except for the increased coverage length, the same terms and conditions apply to the extended warranty as apply to the standard warranty.

Common Accessories

6186
 
The 6186 connects the PS100 to an external 12-V flooded battery such as a deep-cycle marine or RV battery. This cable was previously shipped as part of the PS100, but was made a separately ordered accessory effective 14 August 2006.
SP10
 
SP10 10W Solar Panel, 20ft Cable
 
The SP10 solar panel provides a 10 W maximum peak power, 9 W guaranteed minimum power, 0.59 A current at peak, and 16.8 V voltage at peak.
Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the datalogger.
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a pre-wired enclosure.
-C -C w/ ET/CS110 Connector
With the -C option, the cable terminates in a connector that attaches to a CS110 Electric Field Meter or an ET-series weather station. This is equivalent to the -LC version available for some sensors.
Mounting Options - show details
-SM -SM Std Mounting Kit
Standard mounting to allow solar panel to be mounted directly to the leg of a tower or crossarm.
-EM -EM Extended Mounting Kit
Extended Mounting Kit allows the solar panel to be mounted on a tower or crossarm that puts the panel approximately 25.4 cm (10 in.) from the mast. This reduces shadows on the solar panel from other components or guy wires, which negatively affects the performance of the solar panel. It does, however, increase the wind load on the system.
SP20
 
SP20 20W Solar Panel, 15ft Cable
 
The SP20 solar panel provides a 20 W maximum peak power, 18 W guaranteed minimum peak power, 1.19 A current at peak, and 16.8 V voltage at peak.
Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the datalogger.
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a pre-wired enclosure.
Mounting Options - show details
-SM -SM Std Mounting Kit
Standard mounting to allow solar panel to be mounted directly to the leg of a tower or crossarm.
-EM -EM Extended Mounting Kit
Extended Mounting Kit allows the solar panel to be mounted on a tower or crossarm that puts the panel approximately 25.4 cm (10 in.) from the mast. This reduces shadows on the solar panel from other components or guy wires, which negatively affects the performance of the solar panel. It does, however, increase the wind load on the system.

Other Accessories

A100
 
A100 Null Modem Adapter for PS1X0/200 or CH1X0/200
 
The A100 adapter attaches to the PS100 to provide a null modem connection. This functionality is required in a station where a datalogger will not be present, such as a phone-to-RF base station.

Please note that one A100 or A105 can be used at a time. Also note that early PS100s were not compatible with the A100; PS100s shipped after 20 January 2004 (serial numbers 1391 and higher) are compatible.
Warranty Lengths
-SW -SW Standard 1yr Warranty
-XW -XW 4yr Warr Extension
A105
 
A105 12V Terminal Expansion Adapter for PS1X0/200 or CH1X0/200
 
An A105 adapter connected to the PS100 provides four additional 12 V terminals and four additional Ground terminals. The extra terminals may make it easier for the customer to wire multiple continuously powered 12 Vdc devices to the power supply.

Please note that only one A100 or A105 can be used at a time. Also note that early PS100s were not compatible with the A105; PS100s shipped after 20 January 2004 (serial numbers 1391 and higher) are compatible.
Warranty Lengths
-SW -SW Standard 1yr Warranty
-XW -XW 4yr Warr Extension
15988
 
On one end, the 15988 has a plug that inserts into an ac wall socket. On the other end, it has pigtails that insert into the charging terminals of a CR200-series datalogger.
29796
 
29796 Power Supply 24Vdc 1.67A Output, 100-240Vac 1A Input, 5ft Cable
 
The 29796 converts 100 to 240 Vac to a regulated 24 Vdc. The 29796 can be used with the PS100 if it limited to an "average current of no more than 0.25 A." Short-term peak currents can exceed 1 A without problem.
Power Cable Options
-US -US US & Canada Plug
-IP -IP 7 International Plugs
22110
 
22110 Power Supply 24VdC 1.67A Output, 100-240Vac 1A Input for PW Systems
 
The 22110 wall charger outputs 24 Vdc @ 1.67 A and accepts 100 to 240 Vac. The 22110 can be used with the PS100 if it limited to an "average current of no more than 0.25 A." Short-term peak currents can exceed 1 A without problem.
Power Cable Options
-US -US US & Canada Plug
-IP -IP 7 International Plugs

Replacement Parts

395
 
This screw is used to attach the 18688 Heat Sink Cover to the PS100.
18688
 
This ABS plastic cover fits on the heat sink to prevent customers from getting burned.
17200
 
The 17200 connects the internal #6182 sealed-rechargeable battery to the PS100. This cable is fitted with slip-on connectors for the battery posts.
 
The 17646 allows the customer to replace the detachable lid of the PS100 if it is lost or damaged.
6182
 
The 6182 is the internal 7-Ahr sealed rechargeable battery. Please note that batteries purchased prior to Autumn 2004 are not compatible with the PS100. The earlier batteries had leads that were soldered onto the battery posts. The removable 17200 cable is now used.
28490
 
The 28490 includes two wires—one red and one black. These wires differ only in their insulation color; they have the same same length (1 ft) and gage (18 AWG). The red and black wires are used to connect a Campbell Scientific power supply to a datalogger. The 28490 is shipped with our power supplies and may also be purchased as a replacement part.
505
 
These screws, along with the 6044 grommets, are commonly used together to secure our equipment to the backplates of our enclosures.
6044
 
These grommets are commonly used with the 505 screws to secure our equipment to the backplates of our enclosures.