RETIRED ›
This product is no longer available.
Product Details
Typically Ships Within 21 - 28 Days
Restockable Yes
Warranty 1 year
Compliance

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.


Common Accessories

25316
 
The 25316 is a Right-Hand Circular Polarized (RHCP) Yagi antenna with a gain of 11.0 dBi. The 25316 must be "aimed" at the proper azimuth and inclination to "hit" the satellite. An adjustable mounting bracket is included.
COAXNTN-L
 
COAXNTN-L Antenna Cable RG8 w/2 Type N Male Connectors
 
The COAXNTN-L is an RG8/U, low-loss, coaxial cable with a characteristic impedence of 50 ohms. It has two Type N male connectors for attaching the TX312 transmitter to the antenna.
Cable Length - show details
-L ft per antenna cable

Allowed values: 1-500 ft, increments of 1 ft

Recommended length is 15, 25, or 35 ft (4.6, 7.7, or 10.8 m).
21212
 
This 10 ft (3.1 m) roll of 1"-wide black self-vulcanizing tape can help protect the GOES antenna connection. After connecting the coaxial cable to the antenna, wrap the tape around the connectors that are exposed to the environment.
17992
 
The 17992 GPS antenna is both jam resistant and submersible for greater reliability under field conditions. It requires a 18017 antenna cable and mounting hardware (7623 pipe, CM202-series crossarm, and CM220 or NU-RAIL connector).
18017-L
 
18017-L GPS Antenna Cable
 
The 18017 cable connects the 17992 GPS Antenna to the TX312. The cable has a TNC connector on one end and an SMA connector on the other end. This cable is required if the 17992 is ordered.
Cable Length - show details
-L ft per cable

Allowed values: 1-200 ft, increments of 1 ft

31326
 
For use with the 17992. The 31326 is a GPS RF surge protection kit with flange mounting bracket. It may be flange-mounted to an enclosure backplate or bulkhead-mounted through an enclosure wall. One side of the surge protector connects to a GPS receiver with an SMA antenna connection. The other side connects to the GPS antenna/antenna coaxial cable with Type N connector. The surge protector passes up to ±6 Vdc, commonly needed for active GPS antenna applications.
7623
 
An aluminum pipe is used to mount the GPS antenna to a tripod or tower. The pipe attaches to a crossarm via a 1049 NU-RAIL fitting or CM220 mount. The crossarm is then mounted to a tripod or tower.
1049
 
The 7623 pipe fits into this NU-RAIL fitting. The fitting then attaches to one end of a CM202, CM204, or CM206 crossarm, and the crossarm mounts to a tripod or tower.
CM220
 
The 7623 pipe can be attached to a crossarm using this mount.

Other Accessories

31324
 
The 31324 is a GPS RF surge protection kit that is installed by Campbell Scientific, bulkhead-mounted through the enclosure wall. One side of the surge protector connects to a GPS receiver with an SMA antenna connection. The other side connects to the GPS antenna/antenna coaxial cable with Type N connector. The surge protector passes up to ±6 Vdc, commonly needed for active GPS antenna applications.

Replacement Parts

 
The 7845 is the green, 3-pin SDI-12 connector provided on the TX312 transmitter. It may be purchased to replace a lost or damaged connector.
7843
 
The 7843 is a green, 2-pin power connector provided on the TX312 transmitter. It may be purchased to replace a lost or damaged connector.
 
The 18133 power cable connects the TX312 transmitter to a power supply. It includes the 18889 inline fuse that's listed below.
18889
 
This 7.5 Ampere, fast-blow fuse is contained in the 18133 power cable, and is available as a replacement item.
6044
 
These grommets are commonly used with the 505 screws to secure our equipment to the backplates of our enclosures.
505
 
These screws, along with the 6044 grommets, are commonly used together to secure our equipment to the backplates of our enclosures.