MS-80M-L
MS-80M-L
 
MS-80M-L EKO ISO 9060 Secondary Standard Pyranometer w/RS-485 Modbus Communications
 
MS-80M Options - show details
-L Pricing is in ft cable per sensor

Allowed values: 0-1000 ft, increments of 1 ft
Cable Termination Options
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
How to Order Shipping Information

Add to your Quote List


Product Details
Restockable Yes
Warranty 5 years
Compliance CE Compliance Image RoHS Compliance Image
Ships With
(2) 25866 M5 x 30 mm Stainless-Steel Screw Cap Hex Socket
(4) — Washers (M5)
(2) — Nuts (M5)
(1) — Sun Screen from original mfg
(1) — Temperature Response Measurement Test from original mfg
(1) — Cosine Response Measurement Test from original mfg
(1) — Calibration Certificate (ISO/IEC 17025/9847) from original mfg
(1) — Quick Start Guide from original mfg

Common Accessories

CM255
CM255 Solar Adjustable-Angle Mounting Stand
 
show details
One stand is needed per pyranometer. The CM255 is one of four options. The CM255 is used to mount the MS-80M-L at an angle.
CM256
CM256-SP
 
CM256 Adjustable Plane & Angle Solar Mounting Stand
 
show details
The CM256 adjustable-angle, adjustable-plane mounting stand further simplifies the accurate and precise mounting of a pyranometer, ventilation unit, shadowband radiometer, or reference cell. Several pyranometer mounting stands have been combined and simplified to make ordering easier and usability friendlier. The CM256 is a combination of the CM255LS pyranometer mount, CM245 reference cell and shadowband mount, 31394 VU01 mount, and 31153 CVF4 mount. In addition, several new sensors are now fully supported such as the SPN1, MS-80(M), SR30, SR05, and IMT reference cell CM325.
Mounting Plate Options - show details
-SP -SP w/Small Mount Plate
This mounting plate option is compatible with the following: MS-40/60/80, MS-40M/60M/80M, SR30, SR05, SR11, SR15, SR20-T2, SR20-D2, SP Lite 2, CMP3/6/10/11/21/22, SMP3/6/10/11/21/22, CGR3/4, and SGR3/4.
-LP -LP w/Large Mount Plate
This mounting plate option is compatible with the following: SPN1, PSP, GPP, and SPP Reference Cell (CS325DM).
-VN -VN w/VU01 or MV-01 Plate
This mounting plate option is compatible with the following: VU01 and MV-01.
-CV -CV w/CVF4 Plate
This mounting plate option is compatible with the following: CVF4.
CM261
CM261-SP-AT
 
CM261 Single-Axis Tracker Mounting Stand
 
show details
The CM261 single-axis tracker pyranometer mount with adjustable plane simplifies the mounting of any pyranometer, ventilation unit, reference cell, or SPN1 to hexagonal, round, and square single-axis torque tubes. The CM261 is a combination and simplification of the CM260 and CM265 to make ordering easier and usability friendlier. The bracket includes provisions for mounting the sensors and ventilation units at different heights, allowing the sensing element to be mounted at the same height as the solar modules.
Mounting Plate Options - show details
-SP -SP w/Small Mount Plate
This mounting plate option is compatible with the following: MS-40/60/80, MS-40M/60M/80M, SR30, SR05, SR11, SR15, SR20-T2, SR20-D2, SP Lite 2, CMP3/6/10/11/21/22, SMP3/6/10/11/21/22, CGR3/4, and SGR3/4.
-LP -LP w/Large Mount Plate
This mounting plate option is compatible with the following: SPN1, PSP, GPP, and SPP Reference Cell (CS325DM).
-VN -VN w/VU01 or MV-01 Plate
This mounting plate option is compatible with the following: VU01 and MV-01.
-CV -CV w/CVF4 Plate
This mounting plate option is compatible with the following: CVF4.
Torque Tube Mounting - show details
-AT -AT for ATI Torque Tube
This torque tube mounting option is compatible with hexagonal torque tubes such as ATI.
-NT -NT for NexTracker T Tube
This torque tube mounting option is compatible with round torque tubes such as NexTracker.
-GT -GT for Generic T Tube
This torque tube mounting option is compatible with square torque tubes up to 11.748 cm (4.625 in.) in height by 13.335 cm (5.25 in.) in width.
CMB200
CMB200-NF
 
CMB200 Crossarm Brace Kit
 
show details
The CMB200 Crossarm Brace Kit is designed to provide additional stability when using a crossarm mounted on Campbell Scientific tripods and towers. This kit provides support for crossarms with heavier or sensitive sensor loads, as well as added stability in higher winds. Each kit includes one brace arm and three sets of mounting brackets.
CMB200 Finish Options - show details
-NF -NF No Special Finish
-BF -BF Flat Black Finish
The black power-coated finish helps with reflections when using the CMB200 to mount solar radiation sensors or other light-sensitive sensors.

Other Accessories

33973
33973 RS-485 to USB Converter
 
show details
The 33973 is an RS-485 to USB converter.
CM275
CM275-TS-BS
 
CM275 Albedometer Mounting Kit
 
show details
The CM275 is a universal solar albedo mounting stand for mounting any downwelling/upwelling combination of pyranometer, ventilation unit, reference cell, or spectral radiometer.
Top Mounting Options
-TS -TS w/Small Mount Plate
-TL -TL w/Large Mount Plate
-TV -TV w/VU01 or MV-01 Plate
-TC -TC w/CVF4 Plate
Bottom Mounting Options
-BS -BS w/Small Mount Plate
-BL -BL w/Large Mount Plate
-BV -BV w/VU01 or MV-01 Plate
-BC -BC w/CVF4 Plate

Replacement Parts

MS-80MCBL-L
 
MS-80MCBL-L MS-80M Replacement Cable
 
show details
The MS-80MCBL-L replacement cable uses pn 9721 cable, which is a Santoprene-jacketed cable with three individually shielded twisted-pair conductors. The individual conductors are 24 AWG tinned, soft-annealed copper (7x32 stranded wire) with a solid polypropylene (105C) insulation with a minimum thickness of 0.015 inches. Insulation colors of the twisted pairs are red/black, green/white, and blue/yellow. An aluminum Mylar shield is grounded via a 24 AWG drain wire. Raw cable is cut to length, does not have heat shrink, and has conductors that are not stripped back. The cable is purchased at a per-foot length.
MS-80MCBL Options - show details
-L Pricing is in ft per cable

Allowed values: 1-1000 ft, increments of 1 ft
Cable Termination Options
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
25866 M5 x 30mm Screw Cap Hex Socket SS
 
show details
The 25866 may be purchased to replace a lost or damaged socket.

Services

33475
33475 Pyranometer ISO 17025 accredited Recalibration to ASTM G167 & ISO 9846 w/Documentation
 
show details
The 33475 recalibration service is performed using an intermittent shade method with a World Radiometric Reference (WRR) traceable AHF cavity radiometer. The 33475 recalibration is ISO 17025 accredited to the following standards: ASTM G167 and ISO 9846.
33476
33476 Solar Sensor ISO 17025 accredited Recalibration to ASTM E824 w/Documentation
 
show details
The 33476 recalibration service is performed using a reference group of pyranometers traceable to World Radiometric Reference (WRR). This recalibration is ISO 17025 accredited to ASTM E824 standard.
33477
33477 Solar Sensor ISO 17025 accredited Recalibration to ASTM G207 w/Documentation
 
show details
The 33477 recalibration service is performed indoors using a reference pyranometer of the same make and model. Reference pyranometers are traceable to the World Radiometric Reference (WRR). This recalibration is ISO 17025 accredited to ASTM G207 standard.