Regulators / CH100
RETIRED ›
This product is no longer available and has been replaced by: CH150. Some accessories, replacement parts, or services may still be available.
CH100
 
CH100 12 V Charging Regulator
 

Other Accessories

BP12
 
The BP12 battery pack has a 12 Ah rating and can power a Campbell Scientific system that has components that have above-average power requirements, such as satellite transmitters.
A100
 
A100 Null Modem Adapter for PS1X0/200 or CH1X0/200
 
The A100 adapter is used with the CH100 to provide a null modem connection. The null modem ports allow two modems to "talk" to each other without a datalogger in between. This functionality is required in a station where a datalogger will not be present, such as a phone-to-RF base station.

Please note that only one A100 or A105 can be used at a time.
Warranty Lengths
-SW -SW Standard 1yr Warranty
-XW -XW 4yr Warr Extension
BP24
 
The BP24 battery pack has a 24 Ah rating and can power a Campbell Scientific system that has components that have above-average power requirements, such as satellite transmitters.
A105
 
A105 12V Terminal Expansion Adapter for PS1X0/200 or CH1X0/200
 
The A105 adapter connected to the CH100 provides four additional 12 V terminals and four additional ground terminals. The extra terminals may make it easier for the customer to wire multiple continuously powered 12 Vdc devices to the power supply.

Please note that only one A100 or A105 can be used at a time.
Warranty Lengths
-SW -SW Standard 1yr Warranty
-XW -XW 4yr Warr Extension
15988
 
On one end, the 15988 has a plug that inserts into an ac wall socket. On the other end, it has pigtails that insert into the charging terminals of a CR200-series datalogger.
29796
 
29796 Power Supply 24Vdc 1.67A Output, 100-240Vac 1A Input, 5ft Cable
 
The 29796 converts 100 to 240 Vac to a regulated 24 Vdc. The 29796 can be used with the CH100 if it limited to an "average current of no more than 0.25 A." Short-term peak currents can exceed 1 A without problem.
Power Cable Options
-US -US US & Canada Plug
-IP -IP 7 International Plugs
22110
 
22110 Power Supply 24VdC 1.67A Output, 100-240Vac 1A Input for PW Systems
 
The 22110 wall charger outputs 24 Vdc @ 1.67 A and accepts 100 to 240 Vac. The 22110 can be used with the CH100 if it limited to an "average current of no more than 0.25 A." Short-term peak currents can exceed 1 A without problem.
Power Cable Options
-US -US US & Canada Plug
-IP -IP 7 International Plugs
6186
 
The 6186 connects the CH100 to an auxiliary, 12-V flooded battery such as a deep-cycle marine or RV battery. Cable length is 10 feet. The 6186 was initially shipped as part of the CH100, but was made a separately-ordered accessory effective 14 August 2006.
BP7
 
The 17365 is a 12 Vdc, 7 A h battery. It includes a cable that terminates in pigtails for attachment to the CH100.
SP10
 
SP10 10W Solar Panel, 20ft Cable
 
The SP10 solar panel provides a 10 W maximum peak power, 9 W guaranteed minimum power, 0.59 A current at peak, and 16.8 V voltage at peak.
Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the datalogger.
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a pre-wired enclosure.
-C -C w/ ET/CS110 Connector
With the -C option, the cable terminates in a connector that attaches to a CS110 Electric Field Meter or an ET-series weather station. This is equivalent to the -LC version available for some sensors.
Mounting Options - show details
-SM -SM Std Mounting Kit
Standard mounting to allow solar panel to be mounted directly to the leg of a tower or crossarm.
-EM -EM Extended Mounting Kit
Extended Mounting Kit allows the solar panel to be mounted on a tower or crossarm that puts the panel approximately 25.4 cm (10 in.) from the mast. This reduces shadows on the solar panel from other components or guy wires, which negatively affects the performance of the solar panel. It does, however, increase the wind load on the system.
SP20
 
SP20 20W Solar Panel, 15ft Cable
 
The SP20 solar panel provides a 20 W maximum peak power, 18 W guaranteed minimum peak power, 1.19 A current at peak, and 16.8 V voltage at peak.
Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the datalogger.
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a pre-wired enclosure.
Mounting Options - show details
-SM -SM Std Mounting Kit
Standard mounting to allow solar panel to be mounted directly to the leg of a tower or crossarm.
-EM -EM Extended Mounting Kit
Extended Mounting Kit allows the solar panel to be mounted on a tower or crossarm that puts the panel approximately 25.4 cm (10 in.) from the mast. This reduces shadows on the solar panel from other components or guy wires, which negatively affects the performance of the solar panel. It does, however, increase the wind load on the system.

Replacement Parts

395
 
This screw is used to attach the Heatsink Cover to the CH100.
18688
 
This ABS plastic cover fits on the heatsink to prevent customers from getting burned.
28490
 
The 28490 includes two wires—one red and one black. These wires differ only in their insulation color; they have the same same length (1 ft) and gage (18 AWG). The red and black wires are used to connect a Campbell Scientific power supply to a datalogger. The 28490 is shipped with our power supplies and may also be purchased as a replacement part.
505
 
These screws, along with the 6044 grommets, are commonly used together to secure our equipment to the backplates of our enclosures.
6044
 
These grommets are commonly used with the 505 screws to secure our equipment to the backplates of our enclosures.