AP200 CO2/H2O Atmospheric Profile System
IRGA Options
-GA -GA LI-850-3 Gas Analyzer
Internal Keyboard Options
-NK -NK No Internal Keyboard
-KD -KD w/Keyboard & Display
Enclosure Mounts
-NM -NM No Enclosure Mounting
-MM -MM Tripod Mast Mounting
-LM -LM CM106 Leg Mounting
-TM -TM Tower Mounting
-PM -PM Pole Mounting, 4-10in
AP200 Options - show details
-I -I Pricing is in Intake Assemblies

Allowed values: 4-8 ea, increments of 1 ea

Add to your Quote List

Product Details
Restockable No
Warranty 1 year
Compliance CE Compliance Image RoHS Compliance Image
Ships With
(8) Spare AP200 Intake Filters, 3 micron
(1) 29236 AP200 Enclosure desiccant pack
(1) 29237 AP200 Enclosure fittings & tools pack
(11) Swagelok nut with ferrules

Common Accessories

The 15702 tubing is required for the sample intake assemblies. Order enough tubing to connect all of the sample intake assemblies to the bottom of the enclosure. Maximum roll length is 500 ft.
The 9922 is a 20 AWG power cable used to power a heater on the orifice of each intake assembly. The power cable is normally daisy-chained from the enclosure to all the intake assemblies (e.g. one cable connects the enclosure to an intake assembly, and then another cable connects that intake assembly to the next intake assembly, and so on). Select the total length needed and then cut the cable into smaller lengths on-site to do the daisy-chaining.
CABLEPCBL-L 2-Conductor 16AWG Power Cable
One CABLEPCBL is needed per system; choose the -PT cable termination option. This 16-AWG, two-conductor cable has a Santoprene® jacket and stripped and tinned conductors.
CABLEPCBL-L Options - show details
-L Pricing is in ft per cable

Allowed values: 1-1000 ft, increments of 1 ft

Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the datalogger.
-PW -PW w/Pre-Wire Connector
With the -PW option, there is a pre-wired connector on one end of the cable.
The 38476 is a 16 GB microSD flash-memory card designed for use in harsh conditions often presented by environmental and industrial applications in which customers require higher reliability, endurance, and performance but also seek a cost-effective solution to meet budget-planning requirements.
The 27158 is a 2 GB microSD flash-memory card. This card is designed for use in harsh conditions often presented by environmental and industrial applications. The card uses single-level cell (SLC) memory, which aids in its ability to operate over wide temperature ranges, consume less power, and provide a reliable data-storage medium through more read-write cycles.
The 17752 is a single slot, high-speed reader/writer that allows a computer to read data stored on CompactFlash card. The 17752 connects to the computer's USB port.
The 107 needs to be housed in the 41303-5A, a naturally aspirated, 6-plate radiation shield. The 41303-5A can attach to a crossarm, mast, or a user-supplied pipe with a 1.0" to 2.1" OD.
The RAD06 uses a double-louvered design that offers improved sensor protection from driving rain, snow, and insect intrusion. It also has lower self-heating in bright sunlight combined with higher temperatures (> 24°C (~75°F)) and low wind speeds (< 2m/s (~4.5 mph)), providing a better measurement.
28549 AP200 or CPEC200 AC/DC Power Adapter Kit
The 28549 can be mounted in the AP200 enclosure to supply the AP200 from AC mains power.
Power Cable Options
-NC -NC No Power Cable
-NAC -NAC North America Cable
-EUC -EUC Europe Cable
-UKC -UKC UK/Ireland Cable
-AUC -AUC Australia/NZ Cable
-CNC -CNC China Cable

Other Accessories

The CR1000KD is offered as an accessory for customers who want the keyboard display but do not want it mounted inside the enclosure.
The 31021 may be used as a source of zero air (air free of CO2 and H2O) for performing a field zero of the AP200 gas analyzer.

Replacement Parts

The 29998 is a 2.5 cm diameter, Teflon filter with a 3 micron pore size. It is housed in plastic and has Luer Lock syringe fittings. The 29998 is used to replace dirty filters in the AP200 intakes that have become clogged. AP200 intakes shipped before August 2013 used a different filter and orifice; contact Campbell Scientific for replacement parts or intake upgrades.
The 29999 orifice element is a replacement part for AP200 intake assemblies shipped in August 2013 or later.
The 4905 Single 4-Unit Silica Desiccant Pack is packaged in Tyvek. It is used to desiccate the AP200 enclosure and will periodically need to be replaced.
The 28878 is a replacement humidity indicator card. It provides a visual reference of humidity level inside the enclosure. Colored circles change color from blue to pink to indicate humidity levels of 30%, 40%, and 50% relative humidity.
The 33241 is the drop-in replacement for the AP200 pump.