108
 
108 Temp Probe (-5 to +95C)
 
Cable Length Options - show details
-10 -10 w/10ft per Probe
A 10-ft length is recommended for a probe mounted to a mast/leg at a height of 2 m.
-17 -17 w/17ft per Probe
A 17-ft length is recommended for the following:
  • Probe mounted to a CM202 at a height of 2 m
  • Probe mounted atop a CM106B, CM110, or UT10 via a CM202
-33 -33 w/33ft per Probe
A 33-ft length is recommended for the following:
  • Probe mounted atop a CM115 via a CM202
  • Probe mounted atop a UT20 via a CM202
-50 -50 w/50ft per Probe
A 50-ft length is recommended for a probe mounted atop a UT30 via a CM202.
-U -U w/User Defined Length
-U User Specified Length - show details
-L ft cable per probe

Allowed values: 1-2500 ft, increments of 1 ft

Campbell Scientific recommends:
  • 9 ft length—probe mounted to mast/leg at a 2 m height
  • 11 ft length—probe mounted to a CM202 at 2 m height
  • 14 ft length—probe mounted atop a CM106B, CM110, or UT10 via a CM202
  • 19 ft length—probe mounted atop a CM115 via a CM202
  • 24 ft length—probe mounted atop a UT20 via a CM202
  • 37 ft length—probe mounted atop a UT30 via a CM202
Add two feet to the cable length if you are mounting the enclosure on the leg base of a CM106B, CM110, CM115, or CM120 tripod.
Cable Termination Options - show details
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a prewired enclosure.
-C -C w/ET/CS110 Connector

Add to your Quote List


Product Details
Restockable Yes
Warranty 1 year
Compliance RoHS Compliance Image

Common Accessories

41303-5A
 
When exposed to sunlight, the 108 must be housed in a radiation shield. The 41303-5A 6-plate radiation shield attaches to a crossarm, mast, or a pipe with a 1.0" to 2.1" OD.
RAD06
 
When exposed to sunlight, the 108 must be housed in a radiation shield. The RAD06 uses a double-louvered design that offers improved sensor protection from driving rain, snow, and insect intrusion. It also has lower self-heating in bright sunlight combined with higher temperatures (> 24°C (~75°F)) and low wind speeds (< 2m/s (~4.5 mph)), providing a better measurement.
 
TEMPCAL Calibration Setup Fee
 
The TEMPCAL is available at time of purchase. It provides a single-point calibration and a calibration certificate. The single-point calibration determines the offset at 25°C with an uncertainty of ±0.05°C. Calibration after purchase requires an RMA.
Qty 1-Point Calibration - show details
-CC 1-Pt Calib on Probes

Allowed values: 1-1000 ea, increments of 1 ea

The setup fee is assessed for all probes in the "run"; the 1-point calibration fee is assessed per probe.
 
TEMPCAL2 Calibration Setup Fee
 
The TEMPCAL2 is available at time of purchase. It provides a two-point calibration and a calibration certificate. Calibration after purchase requires an RMA.
Qty 2-Point Calibration - show details
-CC 2-Pt Calib on Probes

Allowed values: 1-1000 ea, increments of 1 ea