05103-L
 
05103-L RM Young Wind Monitor
 
05103-L Options - show details
-L ft cable per sensor

Allowed values: 0-1000 ft, increments of 1 ft

Custom lead lengths are available for up to 1000 feet. Campbell Scientific recommends:
  • 14 ft—sensor mounted atop a CM106B, CM110, or UT10 via a CM202
  • 19 ft—sensor mounted atop a CM115 via a CM202
  • 24 ft—sensor mounted atop a UT20 via a CM202
  • 37 ft—sensor mounted atop a UT30 via a CM202
Cable Termination Options - show details
-PT -PT w/Tinned Wires
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a prewired enclosure.
-CWS -CWS w/CWS900 Connector
With the -CWS option, the cable terminates in a connector that attaches to a CWS900-series interface. Connection to a CWS900-series interface allows this sensor to be used in a wireless sensor network.
-C -C w/ET/CS110 Connector

Add to your Quote List


Product Details
Typically Ships Within 14 - 21 Days
Restockable Yes
Warranty 1 year
Compliance CE Compliance Image

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.

Ships With
(1) 3659 Unthreaded Aluminum Pipe, 1 in. IPS, 12 in. long
(1) Allen wrench from original mfg
(1) Bearing spacer from original mfg
(1) Bearing spacer from original mfg

Common Accessories

17953
 
The 17953 NU-RAIL Crossover Fitting can be used instead of the CM220 to attach this sensor to a crossarm.
CM220
 
The CM220 Right-angle Mounting Bracket attaches this sensor to a crossarm.
CM216
 
The CM216 Sensor Mount provides a connection point for this sensor to be attached to the top of a CM106B, CM110, CM115, or CM120 tripod.

Other Accessories

LLAC4
 
LLAC4 4-Channel Low-Level AC Conversion Module
 
The LLAC4 can be used to increase the number of sensors measured by one datalogger.
Warranty Lengths - show details
-SW -SW Standard 1yr Warranty
At the time of purchase, the LLAC4 includes a standard warranty of 12 months. See our full warranty policy in the LLAC4 manual for the terms and conditions of this warranty.
-XW -XW 4yr Warr Extension
Our Extended Warranty adds 48 months to the standard 12 month warranty, bringing the total warranty period to 60 months. The extended warranty may be purchased only at the time of original product purchase. It may NOT be "added later." Except for the increased coverage length, the same terms and conditions apply to the extended warranty as apply to the standard warranty.

Replacement Parts

13894
 
The 13894 bearings are located in the propeller housing. The bearings can be replaced by mechanically-adept users—especially if they are familiar with replacing bearings in other mechanical systems. Otherwise, replacement at the factory is recommended (requires an RMA).
13895
 
The 13895 bearings allow the wind vane to turn about the axis of the mounting shaft. These bearings are located within the shaft assembly and replacement at the factory is strongly recommended; please request an RMA.
 
The 3659 is an unthreaded pipe used to mount the sensor to a crossarm. The pipe is easily replaced by the user.