RETIRED ›
This product is no longer available and has been replaced by: 03002-L.
03001-L
 
03001-L R. M. Young Wind Sentry Set
 
Product Details
Typically Ships Within 21 - 28 Days
Restockable Yes
Warranty
Compliance

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.


Other Accessories

1049
 
This NU-RAIL Slip-on Offset Crossover fitting attaches to one end of CM202, CM204, or CM206 Crossarm. It provides essentially the same functionality as the CM220."
CM220
 
The CM220 Right Angle Mounting Bracket is used to mount this sensor to a crossarm or a user-supplied 1" IPS pipe.

Formerly ordered as the -SM option.
CM216
 
The CM216 Sensor Mount provides a connection point for this sensor to be attached to the top of a stainless steel CM110, CM115, or CM120 Tripod.

Replacement Parts

 
03101CBL-L 03101-L Replacement Wind Speed Cable
 
The 03101CBL cable attaches to the anemometer. It consists of a 22 AWG cable with a Santoprene jacket and a connector. The 03101CBL can easily be replaced by the user.
03101CBL-L Options - show details
-L ft per sensor cable

Allowed values: 1-1000 ft, increments of 1 ft

Custom lead lengths are available for up to 1000 feet. Campbell Scientific recommends:
  • 14 ft—sensor mounted atop a CM106B, CM110, or UT10 via a CM202
  • 19 ft—sensor mounted atop a CM115 via a CM202
  • 24 ft—sensor mounted atop a UT20 via a CM202
  • 37 ft—sensor mounted atop a UT30 via a CM202
Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the datalogger.
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a prewired enclosure.
 
03301CBL-L 03001-L Replacement Wind Direction Sensor Cable
 
The 03301CBL-L cable attaches the vane. It consists of a 22 AWG cable with a Santoprene jacket and a connector. The 03301CBL can easily be replaced by the user.
Cable Length - show details
-L ft per sensor cable

Allowed values: 1-1000 ft, increments of 1 ft

Custom lead lengths are available for up to 1000 feet. Campbell Scientific recommends:
  • 14 ft—sensor mounted atop a CM106B, CM110, or UT10 via a CM202
  • 19 ft—sensor mounted atop a CM115 via a CM202
  • 24 ft—sensor mounted atop a UT20 via a CM202
  • 37 ft—sensor mounted atop a UT30 via a CM202
 
The 4609 3-cup anemometer assembly can be easily replaced by the user.
 
Replacement of the 4610 Vane Assembly is difficult as it requires calibration of potentiometer after replacement. Returning the sensor to the factory is recommended. Please request assistance.
6700
 
Replacement of the 6700 Potentiometer is difficult because it requires the potentiometer be soldered into place, and the potentiometer needs to be recalibrated after replacement. Returning the sensor to the factory is recommended. Please request assistance.
 
Replacement of the 6701 Anemometer Coil is difficult; it requires that the coil be soldered into place and the sensor be recalibrated after replacement. Returning the sensor to the factory is recommended. Please request assistance.
6702
 
The 6702 provides a shielded bearing with oil lube. The bearings can be replaced by the user. Two are required.