024A-L
024A-L
 
024A-L Met One Wind Direction Sensor
 
024-L Options - show details
-L ft cable per sensor

Allowed values: 0-1000 ft, increments of 1 ft

Custom lead lengths are available for up to 1000 feet. Campbell Scientific recommends:
  • 14 ft—sensor mounted atop a CM106B, CM110, or UT10 via a CM202
  • 19 ft—sensor mounted atop a CM115 via a CM202
  • 24 ft—sensor mounted atop a UT20 via a CM202
  • 37 ft—sensor mounted atop a UT30 via a CM202
These lead lengths assume the sensor is mounted atop the tripod/tower via a CM202 crossarm.
Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the datalogger.
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a pre-wired enclosure.
How to Order

Add to your Quote List


Product Details
Typically Ships Within 14 - 21 Days
Restockable Yes
Warranty 1 year
Compliance CE Compliance Image

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.

Ships With
(1) — #1124 Pipe w/ #493 screw
(1) — NIST Traceable Calibration Certificate & MIL-STD-45662A
(1) 024ACBL-L Replacement Cable for 024A Wind Vane
(1) — Manual from original mfg

Common Accessories

17953
17953 1 x 1 inch Nurail Crossover Fitting
 
show details
This NU-RAIL® Slip-on Offset Crossover fitting can be used as an alternative to the CM220. It attaches the sensor to a CM200-series crossarm.
CM220
CM220 Right Angle Mounting Kit
 
show details
The CM220 Right-angle Mounting Bracket attaches this sensor to a CM200-series crossarm.

Formerly ordered as the -SM option.
CM216
CM216 Sensor Mounting Kit for Top of SS Tripod Mast for CM110-series
 
show details
The CM216 Sensor Mount provides a connection point for this sensor to be attached to the top of a CM106B, CM110, CM115, or CM120 Tripod.

Replacement Parts

024ACBL-L
 
024ACBL-L 024A-L Replacement Cable
 
show details
The 024ACBL-L cable consists of 22 awg conductors insulated in polypropylene and shielded in a 2-twisted pair configuration; the cable jacket is composed of Santoprene®. The 024ACBL has a 6-pin, mil-spec connector and user-specified cable length. A 1K 0.01% completion resistor is included in the pigtail.
024ACBL-L Options - show details
-L ft per sensor cable

Allowed values: 1-1000 ft, increments of 1 ft

Custom lead lengths are available for up to 1000 feet. Campbell Scientific recommends:
  • 14 ft—sensor mounted atop a CM106B, CM110, or UT10 via a CM202
  • 19 ft—sensor mounted atop a CM115 via a CM202
  • 24 ft—sensor mounted atop a UT20 via a CM202
  • 37 ft—sensor mounted atop a UT30 via a CM202
Cable Termination Options - show details
-PT -PT w/Tinned Wires
With the -PT option, the cable terminates in pigtails that connect directly to the datalogger.
-PW -PW w/Pre-Wire Connector
With the -PW option, the cable terminates in a connector that attaches to a prewired enclosure.
16901
16901 014A, 024A, or 034A Replacement Turret Label
 
show details
The 16901 turret label is easily replaced by the customer. This label serves to repel water and is placed over the small access hole in the turret to reduce ingress by water.
2905 Replacement Potentiometer for 024A or 034A
 
show details
The 2905 10K potentiometer is difficult to replace, and requires recalibration after replacement. Factory replacement is recommended (bearings are also replaced).