GRANITE10
 
GRANITE10 Measurement & Control Data Acquisition System
 
Duty Options - show details
-SD -SD Standard Duty
The -SD option has a warranty length of 3 years.
-XD -XD Extended Duty
The Extended Duty (-XD) option of the GRANITE 10 provides extra protection and maximum flexibility for demanding applications:
  • Extended Warranty – A two-year warranty extension for a total of five years
  • Extended Temperature Range (-55° to +85°C) – Each unit is fully production tested over the entire extended range.

Add to your Quote List


Product Details
Restockable Yes
Warranty 3 years
Compliance CE Compliance Image RoHS Compliance Image
Ships With
(1) 34750 Parts Included Kit for the GRANITE9 and GRANITE10

Common Accessories

29796
 
29796 Power Supply 24Vdc 1.67A Output, 100-240Vac 1A Input, 5ft Cable
 
A charging source may be needed. The 29796 converts 100 to 240 Vac to a regulated 24 Vdc. The 29796 comes standard with a USA/Canada plug, with an option to add a kit for international use. The cable is 5 ft long and terminates in pigtails with "+" and "-" labels.
Power Cable Options
-US -US US & Canada Plug
-IP -IP 7 International Plugs
27158
 
Several options of removable memory cards are available. The 27158 is one option. The 27158 is a 2 GB microSD flash-memory card. This card is designed for use in harsh conditions often presented by environmental and industrial applications. The card uses single-level cell (SLC) memory, which aids in its ability to operate over wide temperature ranges, consume less power, and provide a reliable data-storage medium through more read-write cycles.
33288
 
Several options of removable memory cards are available. The 33288 is one option. The 33288 is an 8 GB microSD flash-memory card. This card is designed for use in harsh conditions often presented by environmental and industrial applications. The card uses single-level cell (SLC) memory, which aids in its ability to operate over wide temperature ranges, consume less power, and provide a reliable data-storage medium through more read-write cycles.
38476
 
Several options of removable memory cards are available. The 38476 is one option. The 38476 is a 16 GB microSD flash-memory card designed for use in harsh conditions often presented by environmental and industrial applications in which customers require higher reliability, endurance, and performance but also seek a cost-effective solution to meet budget-planning requirements.
35691
 
The 35691 can be purchased as an accessory to mount the 7.62 cm (3 in.) GRANITE™ modules on a DIN-Rail instead of the standard backplate mounting.
28899
 
An RJ45 cable may be needed, and several options are available. The 28899 is one option. The 28899 is a 2 ft, unshielded CAT6 network cable with RJ45 connectors. It is typically used to connect CDM devices together or to an SC-CPI. This cable is also used to connect one of our many Ethernet-capable products to an Ethernet device or network connection.
28900
 
An RJ45 cable may be needed, and several options are available. The 28900 is one option. The 28900 is a 10 ft, unshielded, CAT5e network cable with RJ45 connectors. It is typically used to connect one of our many Ethernet-capable products to an Ethernet device or network connection.
28901
 
An RJ45 cable may be needed, and several options are available. The 28901 is one option. The 28901 is a 50 ft, unshielded, CAT5e cable with RJ45 connectors. It is typically used to connect CDM devices together or to a data logger. This cable can also be used to connect one of our many Ethernet-capable products to an Ethernet network connection.
CAT5UCBL-L
 
CAT5UCBL-L CAT5e Cable Unshielded w/RJ-45 Connectors
 
An RJ45 cable may be needed, and several options are available. The CAT5UCBL-L is one option. This is an RJ45 cable that is ordered to a customer-defined length. We have created this so when people are connecting CDM devices together or to a data logger, they can have a custom-length cable if they do not want one of our set-length cables, which are 6 in., 2 ft, 10 ft, or 50 ft.
Cable Length - show details
-L Pricing is in ft per cable

Allowed values: 1-1000 ft, increments of 1 ft

HUB-CPI
 
The HUB-CPI allows eight CPI (CAN peripheral interface) devices to be connected together in parallel. Typically, this configuration includes one data logger and up to seven CDMs (Campbell distributed modules) or sensors that use CPI.
29370
 
One 29370 is needed for each CPI network. Among the items included in the 29370 kit is a roll of yellow vinyl electrical tape to distinguish Ethernet cables that use CPI protocol from similar cables used for TCP/IP.
31326
 
A 31326 may be needed for GPS output. The 31326 is a GPS RF surge protection kit with flange mounting bracket. It may be flange-mounted to an enclosure backplate or bulkhead-mounted through an enclosure wall. One side of the surge protector connects to a GPS receiver with an SMA antenna connection. The other side connects to the GPS antenna/antenna coaxial cable with Type N connector. The surge protector passes up to ±6 Vdc, commonly needed for active GPS antenna applications.

Other Accessories

31055
 
The 31055 adapts an RS-232/CPI RJ45 port to a DB9 male connector. This cable is offered to make it easier to connect a DCE serial device, such as a cellular modem, to the RS-232/CPI port. 
31056
 
The 31056 adapts an RS-232/CPI RJ45 port to a DB9 female connector. This cable is offered to make it easier to connect a DTE serial device, such as a computer or terminal server, to the RS-232/CPI port. 
31897
 
The 31897 can be plugged into the RJ45 RS-232 port on a data logger to connect the data logger to an RS-232 sensor. 
CR1000KD
 
The CR1000KD is a portable keyboard and display screen for our data loggers that have a CS I/O port. It allows you to check the data logger's status, display or plot sensor readings and stored values, and enter numeric data or change port/flag state. One CR1000KD may be carried from station to station in a data logger network.
SC110
 
The SC110 consists of two cables to connect a data logger with RS-232 DCE and DTE devices. One end of each cable provides stripped, tinned leads for attachment to the control ports on a data logger. On the other end, one of the cables is fitted with a 9-pin male connector, and the other cable is fitted with a 9-pin female connector.
28558
 
These termination resistor plugs are used in a CPI network.

Replacement Parts

8125
 
The 8125 is a small, flat-bladed screwdriver that is extremely useful for opening the guillotine terminals on our data loggers and measurement control devices.
505
 
These screws, along with the 6044 grommets, are commonly used together to secure our equipment to the backplates of our enclosures.
6044
 
These grommets are commonly used with the 505 screws to secure our equipment to the backplates of our enclosures.
28490
 
The 28490 includes two wires—one red and one black. These wires differ only in their insulation color; they have the same same length (1 ft) and gage (18 AWG). The red and black wires are used to connect a Campbell Scientific power supply to a data logger.
28898
 
The 28898 is a 6 in., unshielded, CAT6 network cable with RJ45 connectors. It is typically used to connect CDM devices together or to an SC-CPI. This cable is also used to connect one of our many Ethernet-capable products to an Ethernet device or network connection.
27555
 
The 27555 is a USB Type A to Micro B, male-to-male cable, 6 to 6.5 ft long. It connects devices using the Micro B interface to a USB port on a computer.
16005
 
The 16005 is a unity gain (0 dBd), 1/2 wave whip, omnidrectional antenna that can be used with our 2.4 GHz radio products with RPSMA antenna connectors. It features an articulating knuckle joint for easy orientation, weatherized jacket for outdoor applications, and internal counterpoise for ground plane independence.
31182
 
The 31182 is a magnetic mount GPS patch antenna. It is typically used where GPS reception is readily available and concern is low for snow buildup completely covering the antenna. The 31182 is also commonly used in cost-sensitive applications or applications that require a small-sized, low-profile antenna.
34774
 
The 34774 is the mini-blade five-amp fuse kit that can be ordered to replace the fuses that ship with the GRANITE™9 and GRANITE™10.
13519
 
The 13519 is a 3.6 Vdc, 1.2 Ahr, 1/2 AA size cell battery. The 13519 needs to be periodically replaced. Typically, the battery is replaced when its voltage is at or below 2.7 Vdc.
34702
 
The 34702 is the external cover for the lithium battery on the GRANITE™6, GRANITE™9, and GRANITE™10. It ships attached to these data-acquisition systems but can be ordered as a replacement.
34847
 
The 34847 is the small screw used to secure the lithium battery cover on the GRANITE™6, GRANITE™9, and GRANITE™10. It ships with these data-acquisition systems but can be purchased as a replacement.
29474
 
The 29474 is a ground lug with a slotted notch on its top that may be purchased to replace a lost or damaged ground lug. 
34463
 
The 34463 is the removable terminal plug connector for the CAN channels on the GRANITE™10. It ships with the GRANITE™10 but can be purchased as a replacement or when it is beneficial to leave the connector attached to the sensors while using a single data-acquisition system in different locations.
34464
 
The 34464 is the 20-pin removable terminal plug connector for the GRANITE™9 and GRANITE™10. It ships with these data-acquisition systems but can be purchased as a replacement or when it is beneficial to leave the connector attached to the sensors while using a single data-acquisition system in different locations.
34614
 
The 34614 is the four-position power connector that ships with the GRANITE™ data-acquisition and measurement modules. It can be purchased as a replacement.
34750
 
The 34750 consists of the 28898 6 in. RJ45 to RJ45 cable, the 27555 USB 2.0 cable, the 9634 black and 9635 red power wires, the 8125 flat-bladed screwdriver, the 31182 GPS antenna, the 16005 omnidirectional 1/2 wave whip antenna, the 34774 GRANITE 9 and 10 replacement fuse kit, four 505 screws, and four 6044 grommets.

Services

Campbell Scientific offers NIST traceable calibration for this product, as well as full maintenance, repair, and temperature testing services. Contact us for a returned material authorization (RMA) number.

 
This service requires an RMA (Returned Material Authorization) from Campbell Scientific. The data-acquisition system is fully bench-tested to ensure that its original specifications are met. The internal lithium battery and desiccant pack are replaced, and the operating system is updated to the newest version. It is then tested over the system's published temperature range. A NIST traceable calibration certificate is provided. The system is returned with all settings restored to default unless otherwise specified. If the system requires repair, those costs will be added to the invoice.