Tripods / CM115
CM115 15 ft Stainless-Steel Tripod with Grounding and Guy Kit
Strong, Tilting Mast
Easy to set up and take down
weather applications water applications energy applications gas flux and turbulence applications infrastructure applications soil applications


The CM115 is a 15-foot instrumentation tripod that supports the attachment of sensors, mounts, solar panels, and environmental enclosures. Constructed from stainless steel, the CM115 is easier to transport to remote locations. The tripod can be deployed in uneven terrain and at varying heights. To facilitate sensor attachment, the tripod mast pivots at the leg junction.

Read More

Benefits and Features

  • Strong and lightweight
  • Most joints are locked with pins that are simple to insert and remove
  • Individually-adjustable legs allow installation over uneven terrain
  • Includes grounding kit


Detailed Description

The CM115 is used as a portable instrument mount in a variety of applications. For meteorological applications, tripods augmented with mounts support the attachment of sensors such as wind sets, pyranometers, and temperature/relative humidity probes. Barometers, soil temperature and moisture probes, and rain gages are also used with tripod-based weather stations. For non-meteorological applications, tripods can provide a portable instrument mount for enclosures and a mounting point for antennas.

UV-resistant cable ties, grounding kit, and six spikes for the tripod feet are included with the CM115.

Two duckbill anchor kits are offered for securing the guy wires (see Ordering Information). Duckbill anchors are not required to use the guy-wire kits. Without them, the guy wires are run from the mast to the feet of the tripod. Duckbill anchors are recommended for areas subjected to higher winds. They allow the guy wires to be anchored at points beyond the feet, thereby increasing the rating of the tripod for higher winds.

The stainless-steel version of the CM115 began shipping in March 2007. Previous versions were made of aluminum.


Material 304 stainless steel
Vertical Load Limit 45 kg (100 lb)
Mast Sections 2
Base Diameter 2 m (7 ft) with legs extended
Insert Outer Diameter 4.45 cm (1.75 in.)
Height 4.5 m (15.2 ft) with mast insert
Dimensions 15 x 15 x 145 cm (6 x 6 x 57 in.) of collapsed tripod
Shipping Weight 18 kg (40 lb)


Outer Diameter 4.8 cm (1.9 in.)
Pipe Size 3.81 cm (1.5 in.) IPS
  • 2.8 m (9.3 ft) without insert
  • 4.1 m (13.3 ft) with insert

Wind Load Recommendation

-NOTE- This recommendation assumes the guy wire anchors are able to hold at least 1.8 kN (400 lbf).
Sustained Wind
  • 90.52 kph (56.25 mph) guyed at feet
  • 120.7 kph (75 mph) guyed at 60°
Gust Tolerance
  • 114.7 kph (71.25 mph) guyed at feet
  • 152.9 kph (95 mph) guyed at 60°

Tote Bag

Diameter 20 cm (8 in.)
Length 152 cm (60 in.)


Note: The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.

Mounting Equipment

Product Compatible Note
019ALU (retired)
UT018-5 (retired)

Additional Compatibility Information


The ENC16/18 cannot be mounted to the CM115's leg base, as the enclosure is too large for the space. 

Enclosure Brackets

The “-MM” mount option for our environmental enclosures is intended for mounting the enclosure to a tripod's mast. An enclosure ordered with this option will be shipped with a three-piece bracket mounted to the top of the enclosure and an identical three-piece bracket mounted to the bottom of the enclosure.

The "-LM" mount option for our environmental enclosures allows the enclosure to be attached to the leg base of the CM115. This option includes a metal flange, two brackets, and a 2.5" u-bolt. The brackets attach to the right and left side of the enclosure, and the flange attaches to the tripod near the mast. The flange fits into a notch in one of the brackets, and the other bracket connects to a tripod leg via the u-bolt.

Videos & Tutorials

Frequently Asked Questions

Number of FAQs related to CM115: 1

  1. Installation time varies and depends on the instrumentation to be attached to the mast, as well as how the guy wires are anchored (for example, to the feet or using Duckbill anchors). On level ground with the guy wires attached to the feet, the installation time is approximately 60 minutes. Campbell Scientific recommends the assistance of one person at the base of the mast and two additional people to help raise the mast with the guy wires.

Privacy Policy Update

We've updated our privacy policy.  Learn More

Cookie Consent

Update your cookie preferences.  Update Cookie Preferences