Resource Center

Hydro-Link (Zip File)

Software applications, data logger operating systems, firmware, and drivers for Campbell Scientific products

Hydro-Link (Zip File)

v2.02.16

Hydro-Link is a browser-based user interface that can be run from a PC or directly from the datalogger. Currently this is only used on the CR300-series dataloggers. Normally, when Hydro-Link is loaded onto and run directly from a CR300-series datalogger, the datalogger would have the Wi-Fi option or a CR310 with Ethernet. When running Hydro-Link from the datalogger, smartphones and tablets can also be used to display the interface.

Follow the Hydro-Link Installation Guide to install from the zip file.

Revision History

v2.02.16June 14, 2022

Minor
Replace any NAN value in CV_Rain_Accum with zero on startup (ClimaVue)
Minor
Don't append the current rain reading to CV_Rain_Accum when it is given as NAN (ClimaVue)
Minor
Make it possible to edit Accumulated Precipitation (CV_Rain_Accum) from the dashboard (ClimaVue)

v2.02April 15, 2021

New Feature
German version is now available.
New Feature
Added Every 15th, 20th, 24th, 30th, and 60th for possible "Included Values" (decimation) selections in GOES configuration.
Minor
Upgraded to CR3xx OS v10.04.
Minor
The Configuration screen isn't accessible in the PC version when the station's configuration file was created by a different language version of HydroLink
Minor
Fixed the PC version to collect Data in TOB1 and XML file format as well as TOA5.
Minor
Fixed the Hourly Window Alarm - the alarm was previously not triggering properly between the hourly start time and hourly stop time.
Minor
The TX325 interface is disabled if it was previously used but not currently in use.
Minor
Any PPP configuration used previously by an external cell modem is removed when initializing GOES or Iridium communications.
Minor
Improved SDI-12 address uniqueness checking.
Minor
Improved message reporting for PakBus encryption login errors.
Minor
Clarify that the datalogger clock synchronization triggered from the dashboard happens only once per trigger execution.

v2.01June 26, 2020

New Feature
Added support for SoilVUE SDI-12 soil moisture sensor.
New Feature
Added support for ClimaVUE complete weather sensor.
New Feature
Added support for ARG314 tipping bucket rain gage.
New Feature
Added support for LevelVUE B10 water level sensor.
New Feature
Added support for the TX325.
New Feature
Added ability to perform a system update from the Configuration page
Update tab.
Major
Changes for compatibility with CR300 OS version 10.02.
Minor
Added ability to reset TX325 to factory defaults.
Minor
Added the ability set the Random Transit Interval to a minimum of 1 minute (TX325 only).
Minor
Ability to trigger a random transmission for the TX325 and write the event to a log.
Minor
Set a fixed clock synchronization time for the TX321 (daily, 12:05 PM).
Minor
Added more diagnostic values to GOES_Status_Table.
Minor
Improved ETo calculated value by allowing user to manually enter latitude/longitude/elevation.
Minor
For ClimaVUE, ETo calculations can use GPS values when available (by entering 0 for latitude/longitude/elevation). Non-zero values should be used when GPS is not available or to override the GPS values.
Minor
Changed ETo so that an ET calculation will not be performed if the measurement interval is greater than 1 hour.
Minor
Barometric pressure for ClimaVUE is adjusted to sea level based on elevation.
Minor
Added optional SDI-12 parameters for CS451, CS475A, and generic.
Minor
Increased the maximum number of generic SDI-12 values returned from 9 to 15.
Minor
Renamed the "PakBus/TCP Server Address" setting to "Datalogger/Router IP Address".
Minor
When performing an update from previous Hydro-Link versions, configuration files will be copied from the CSI drive to the CPU drive.
Minor
Added caution messages to inform users about incompatibility with older versions.
Minor
Added a message to inform the user that changes cannot be made to the configuration when logged in as a Read Only user.
Minor
Changed storage location of Settings.json and dash-config.json from CSI to CPU drive.
Minor
Dashboard cosmetic changes.
Minor
Added units and labels to all dashboard variable types.
Minor
Added an "Enable All Outputs" option for sensors with more than four outputs.
Minor
Changed the allowed variable name length to avoid compilation errors.
Minor
Fixed a data type problem with the TCP Port value that could cause connection failures if the value was modified.
Minor
Fixed a problem where the time displayed for the Next Scheduled Transmission could be a very large number.
Minor
Made changes to avoid unknown SHEF code indicators in data.
Minor
Added copyright information to support files.
Minor
Updated desktop app to Electron version 7.1.2.