Resource Center

Hydro-Link (Windows Install)

Software applications, data logger operating systems, firmware, and drivers for Campbell Scientific products

Hydro-Link (Windows Install)

v2.02.16

Hydro-Link is a browser-based user interface that can be run from a PC or directly from the datalogger.  Currently this is only used on the CR300-series dataloggers.  Normally, when Hydro-Link is loaded onto and run directly from a CR300-series datalogger, the datalogger would have the Wi-Fi option or a CR310 with Ethernet.  When running Hydro-Link from the datalogger, smartphones and tablets can also be used to display the interface.      

Revision History

v2.02.16June 14, 2022
Sign in to download
  • Minor1.
    Replace any NAN value in CV_Rain_Accum with zero on startup (ClimaVue)
  • Minor2.
    Don't append the current rain reading to CV_Rain_Accum when it is given as NAN (ClimaVue)
  • Minor3.
    Make it possible to edit Accumulated Precipitation (CV_Rain_Accum) from the dashboard (ClimaVue)
v2.02April 15, 2021
Sign in to download
  • New Feature1.
    German version is now available.
  • New Feature2.
    Added Every 15th, 20th, 24th, 30th, and 60th for possible "Included Values" (decimation) selections in GOES configuration.
  • Minor3.
    Upgraded to CR3xx OS v10.04.
  • Minor4.
    The Configuration screen isn't accessible in the PC version when the station's configuration file was created by a different language version of HydroLink
  • Minor5.
    Fixed the PC version to collect Data in TOB1 and XML file format as well as TOA5.
  • Minor6.
    Fixed the Hourly Window Alarm - the alarm was previously not triggering properly between the hourly start time and hourly stop time.
  • Minor7.
    The TX325 interface is disabled if it was previously used but not currently in use.
  • Minor8.
    Any PPP configuration used previously by an external cell modem is removed when initializing GOES or Iridium communications.
  • Minor9.
    Improved SDI-12 address uniqueness checking.
  • Minor10.
    Improved message reporting for PakBus encryption login errors.
  • Minor11.
    Clarify that the datalogger clock synchronization triggered from the dashboard happens only once per trigger execution.
v2.01June 26, 2020
Download unavailable
  • New Feature1.
    Added support for SoilVUE SDI-12 soil moisture sensor.
  • New Feature2.
    Added support for ClimaVUE complete weather sensor.
  • New Feature3.
    Added support for ARG314 tipping bucket rain gage.
  • New Feature4.
    Added support for LevelVUE B10 water level sensor.
  • New Feature5.
    Added support for the TX325.
  • New Feature6.
    Added ability to perform a system update from the Configuration page
  • 7.
    Update tab.
  • Major8.
    Changes for compatibility with CR300 OS version 10.02.
  • Minor9.
    Added ability to reset TX325 to factory defaults.
  • Minor10.
    Added the ability set the Random Transit Interval to a minimum of 1 minute (TX325 only).
  • Minor11.
    Ability to trigger a random transmission for the TX325 and write the event to a log.
  • Minor12.
    Set a fixed clock synchronization time for the TX321 (daily, 12:05 PM).
  • Minor13.
    Added more diagnostic values to GOES_Status_Table.
  • Minor14.
    Improved ETo calculated value by allowing user to manually enter latitude/longitude/elevation.
  • Minor15.
    For ClimaVUE, ETo calculations can use GPS values when available (by entering 0 for latitude/longitude/elevation). Non-zero values should be used when GPS is not available or to override the GPS values.
  • Minor16.
    Changed ETo so that an ET calculation will not be performed if the measurement interval is greater than 1 hour.
  • Minor17.
    Barometric pressure for ClimaVUE is adjusted to sea level based on elevation.
  • Minor18.
    Added optional SDI-12 parameters for CS451, CS475A, and generic.
  • Minor19.
    Increased the maximum number of generic SDI-12 values returned from 9 to 15.
  • Minor20.
    Renamed the "PakBus/TCP Server Address" setting to "Datalogger/Router IP Address".
  • Minor21.
    When performing an update from previous Hydro-Link versions, configuration files will be copied from the CSI drive to the CPU drive.
  • Minor22.
    Added caution messages to inform users about incompatibility with older versions.
  • Minor23.
    Added a message to inform the user that changes cannot be made to the configuration when logged in as a Read Only user.
  • Minor24.
    Changed storage location of Settings.json and dash-config.json from CSI to CPU drive.
  • Minor25.
    Dashboard cosmetic changes.
  • Minor26.
    Added units and labels to all dashboard variable types.
  • Minor27.
    Added an "Enable All Outputs" option for sensors with more than four outputs.
  • Minor28.
    Changed the allowed variable name length to avoid compilation errors.
  • Minor29.
    Fixed a data type problem with the TCP Port value that could cause connection failures if the value was modified.
  • Minor30.
    Fixed a problem where the time displayed for the Next Scheduled Transmission could be a very large number.
  • Minor31.
    Made changes to avoid unknown SHEF code indicators in data.
  • Minor32.
    Added copyright information to support files.
  • Minor33.
    Updated desktop app to Electron version 7.1.2.