Product Details
Typically Ships Within 0 - 7 Days
Restockable Yes
Warranty 1 year
Compliance

The "Typically Ships Within" value is an estimate of the number of calendar days within which this product is ready to ship from Campbell Scientific. Orders with more than 10 built-to-order products will likely increase the time needed to prepare the order for shipping.

To estimate how long it will take to receive an order that contains multiple products, combine the longest Ships Within value with the transit time of the shipping method you select.

Some specialized products have long Ships Within values. Because of this, you might consider submitting a separate order for these products so your other products won't be delayed.

Ships With
(2) 17492 Stainless-Steel U-Bolt Screw 5/16-18 x 2.125 with 2 Silicon Bronze Nuts
(2) 17446 Stainless-Steel U-Bolt Screw 5/16-18 x 1.500 with Silicon Bronze Nuts
(8) 4366 Stainless-Steel Lock Washer 5/16
(8) 4365 Stainless-Steel Flat Washer 5/16

Common Accessories

17953
 
The 17593 NU-RAIL® Slip-on Offset Crossover Fitting is used to mount a sensor with a 1.0" IPS mounting pipe (typically a wind sensor) to the crossarm. It provides equivalent functionality as the CM220 Right Angle Mounting Bracket.
1049
 
The 1049 NU-RAIL® Crossover Fitting is used to mount a sensor with a 0.75" IPS mounting pipe (typically a wind sensor) to the crossarm. It provides equivalent functionality as the CM220 Right Angle Mounting Bracket.
CMB200
 
The CMB200 Crossarm Brace Kit is designed to provide additional stability to the CM206 crossarm mounted on Campbell Scientific tripods and towers. This kit provides support for crossarms with heavier or sensitive sensor loads, as well as added stability in higher winds. Each kit includes one brace arm and three sets of mounting brackets.
CM220
 
The CM220 Right-angle Mounting Bracket attaches a sensor that has a 1" IPS or 0.75" IPS mounting pipe (e.g., most wind sensors) to a CM206 crossarm.
CM230
 
The CM230 Adjustable Inclination Mount secures a directional (Yagi) antenna or a sensor that must be pointed at a specific target (e.g., SI-111, SR50A) to the CM206.
CM225
 
The CM225 can attach one pyranometer or quantum sensor to a CM206 crossarm.
CM235
 
The CM235 can attach one peripheral with a magnetic base (typically antennas) to a CM206 crossarm. Devices that have a magnetic base include our GPS16X-HVS Geographic Position Receiver, GPS antennas, and some short-range omnidirectional antennas.
CM210
 
The CM210 is included with this crossarm. An additional CM210 may be useful if the crossarm will be mounted on a tower. The additional CM210 allows the crossarm to be secured to two of the three vertical risers within the tower.
41003-5
 
This 10-plate Gill radiation shield accommodates one HMP45C probe. The shield's louvered construction allows air to pass freely through the shield thereby keeping the probe at or near ambient temperature.
41303-5A
 
This 6-plate Gill radiation shield accommodates one 107, 108, or HMP60 probe. The shield's louvered construction allows air to pass freely through the shield thereby keeping the probe at or near ambient temperature.
RAD06
 
The RAD06 uses a double-louvered design that offers improved sensor protection from driving rain, snow, and insect intrusion. It also has lower self-heating in bright sunlight combined with higher temperatures (> 24°C (~75°F)) and low wind speeds (< 2m/s (~4.5 mph)), providing a better measurement.

Replacement Parts

CM210
 
The CM210 is included with our CM206 crossarm but may also be ordered separately as a replacement item. It attaches the CM206 to a tripod mast or tower leg.
17492
 
The 17492 provides a 5/16" U-bolt and two nuts. This product is used to mount solar panels, mounts, enclosures, or sensors to a mast, tower, or pole.
17446
 
The 17446 provides a U-bolt and two nuts as a replacement for the original U-bolt and nuts.
4365
 
The 4365 can be purchased to replace a lost or damaged washer.
4366
 
The 4366 may be purchased to replace a lost or damaged washer.