Product Details
Restockable Yes
Warranty 1 year
Compliance
Ships With
(2) 17492 Stainless-Steel U-Bolt Screw 5/16-18 x 2.125 with 2 Silicon Bronze Nuts
(2) 17446 Stainless-Steel U-Bolt Screw 5/16-18 x 1.500 with Silicon Bronze Nuts
(8) 4366 Stainless-Steel Lock Washer 5/16
(8) 4365 Stainless-Steel Flat Washer 5/16

Common Accessories

17953
 
This NU-RAIL® crossover fitting is used to mount a sensor with a 1.0" IPS mounting pipe (typically a wind sensor) to the crossarm. It provides equivalent functionality as the CM220 Right Angle Mounting Bracket.
1049
 
This NU-RAIL® crossover fitting is used to mount a sensor with a 0.75" IPS mounting pipe (typically a wind sensor) to the crossarm. It provides equivalent functionality as the CM220 Right Angle Mounting Bracket.
CMB200
 
The CMB200 Crossarm Brace Kit is designed to provide additional stability to the CM204 crossarm mounted on Campbell Scientific tripods and towers. This kit provides support for crossarms with heavier or sensitive sensor loads, as well as added stability in higher winds. Each kit includes one brace arm and three sets of mounting brackets.
CM220
 
The CM220 Right-Angle Mounting Bracket attaches a sensor that has a 1" IPS or 0.75" IPS mounting pipe (e.g., most wind sensors) to a CM204 crossarm.
CM230
 
The CM230 Adjustable Inclination Mount secures a directional (Yagi) antenna or a sensor that must be pointed at a specific target (e.g., SI-111, SR50A) to the CM204.
CM225
 
The CM225 can attach one pyranometer or quantum sensor to the CM204 crossarm.
CM235
 
The CM235 can attach one peripheral with a magnetic base to the CM204 crossarm. Devices that have a magnetic base include our GPS16X-HVS Geographic Position Receiver, GPS antennas, and some short-range omnidirectional antennas.
CM210
 
The CM210 is included with our CM204 crossarm. An additional CM210 may be useful if the CM204 will be mounted on a tower. The additional CM210 allows the crossarm to be secured to two of the three vertical risers within the tower.
41003-5
 
This 10-plate Gill radiation shield accommodates one HMP45C probe. The shield's louvered construction allows air to pass freely through the shield thereby keeping the probe at or near ambient temperature.
41303-5A
 
This 6-plate Gill radiation shield accommodates one 107, 108, or HMP60 probe. The shield's louvered construction allows air to pass freely through the shield thereby keeping the probe at or near ambient temperature.
RAD06
 
The RAD06 uses a double-louvered design that offers improved sensor protection from driving rain, snow, and insect intrusion. It also has lower self-heating in bright sunlight combined with higher temperatures (> 24°C (~75°F)) and low wind speeds (< 2m/s (~4.5 mph)), providing a better measurement.
RAD10E
 
The RAD10E uses a double-louvered design that offers improved sensor protection from driving rain, snow, and insect intrusion.
RAD14
 
The RAD14 uses a double-louvered design that offers improved sensor protection from driving rain, snow, and insect intrusion.

Replacement Parts

CM210
 
The CM210 is included with our CM204 crossarm but may also be ordered separately as a replacement item. It attaches the CM204 to a tripod mast or tower leg.
17492
 
The 17492 provides a 5/16" U-bolt and two nuts. This product is used to mount solar panels, mounts, enclosures, or sensors to a mast, tower, or pole.
17446
 
The 17446 provides a U-bolt and two nuts as a replacement for the original U-bolt and nuts.
4365
 
The 4365 can be purchased to replace a lost or damaged washer.
4366
 
The 4366 may be purchased to replace a lost or damaged washer.