Toggle navigation
Products
Solutions
Support
About
Home
Products
Solutions
Support
About
Quote List
Contact
Regional Websites
Regional Websites
ภาษาไทย
Africa
Australia
Brasil
Canada
Centro Caribe
Deutschland
España
Europe
France
India
United States
中国
Country Directory
Log In
CR6
Getting Started
Ask a Question
Ask a Question
Table of Contents
1)
Let’s go!
2)
Get Started.
3)
Make a connection.
4)
Tell the CR6 what you need it to do.
5)
Make it yours.
6)
Select Your Communications Option
Previous
Next
Let’s go!
Previous
Next
Looking for product information? Go here:
CR6 Measurement and Control Datalogger
View CR6 Page
CR6 Support Resources
Downloads (5)
CR6 OS - 9/28/22
CR6-RF407 Series OS Update - 7/3/19
CR6 Wifi OS Update - 5/21/21
Device Configuration Utility - 4/20/22
CPI Calculator - 7/6/16
Product Manuals (6)
CR6 Getting Started Guide (PDF)
CR6 Product Manual (online)
CR6 Product Manual (PDF)
CR6-RF451 Communications Setup Guide
Datalogger RF407-Series Spread Spectrum Radio Option
CR6 CRBasic Help (online)
Videos & Tutorials (43)
VSPECT—Understanding the Basics
(3:10)
CR6 Ethernet QuickStart
CR6-RF Communication QuickStart
CR6 Series Wi-Fi QuickStart
CR6 Datalogger | An Introduction
(2:37)
Built-in Web Interface
(2:59)
Webinar | VSPECT—Patented Spectral-Analysis Technology
(48:50)
Campbell Scientific Data Logger Expansion
(8:53)
Ethernet over USB
(2:11)
CR6 Getting Started Tutorial
IP Networking and Data Loggers Part 1
(8:34)
Fundamentals of CRBasic Programming Part 5: Conditional Tables
(10:51)
Datalogger Ethernet Configuration
(2:54)
EZSetup Ethernet Connection
(2:02)
View Data Tutorial
Double-Precision Calculations
(5:50)
CR6-WIFI Datalogger | Setting up a Network
(7:43)
Collect Data Tutorial
Overview and Software Setup (QuickStart Part 1)
(5:24)
Fundamentals of CRBasic Programming Part 4: Programming for Control with Operators and Logical Expressions.
(9:05)
Using a Multiplexer
(8:27)
Programming with Short Cut (QuickStart Part 2)
(5:49)
IP Networking and Data Loggers Part 2
(9:51)
Datalogger Programming
Fundamentals of CRBasic Programming Part 6: Loops
(9:02)
Toolbox for Installation and Maintenance
(2:21)
Use LoggerNet to Send a Program and Collect Data (QuickStart Part 3)
(5:06)
Use PC200W to Send a Program and Collect Data (QuickStart Part 4)
(3:44)
Pipeline and Sequential Modes
(10:04)
Hughes 9502 Inmarsat BGAN Satellite IP Terminal
(13:08)
LoggerNet Software | Changing Variables
(2:33)
Power Budgeting
(4:07)
Certificates of Calibration
(1:05)
SDI-12 Sensors | Transparent Mode
(7:13)
Sending an OS to a Local Datalogger (Part 1)
(5:28)
SDI-12 Sensors | Watch or Sniffer Mode
(3:25)
LoggerNet Software | Network Planner
(4:04)
Sending an OS to a Remote Datalogger (Part 2)
(5:10)
LoggerLink Software | An Introduction
(12:11)
Fundamentals of CRBasic Programming Part 1: Variables
(13:30)
Connect Window Tutorial
Fundamentals of CRBasic Programming Part 2: Tables
(8:53)
Fundamentals of CRBasic Programming Part 3: Writing a Complete Program
(14:51)
FAQs (8)
Why are single-ended measurements used in the
ACPower()
instruction in CRBasic when the outputs of the potential transformer and current transformer are inherently differential?
Does the CR6 use true logic levels for RS-232?
How does the power usage of the CR1000X compare to the power usage of the CR1000 or CR6?
Can the CR6 have simultaneous communications (that is, Ethernet and USB) at the same time between two different computers?
How can a serial modem be connected to a CR6?
If a CPI-enabled device is running and there are skipped scans in the data logger, what can be done?
What is the difference between the microSD cards that Campbell Scientific sells and the cards that are commonly used in the consumer electronics at home?
How many AM16/32B multiplexers can be connected to a data logger at the same time?