Measurement and Control Products for WEATHER Measurement and Control Products for WATER Measurement and Control Products for ENERGY Measurement and Control Products for MACHINES Measurement and Control Products for STRUCTURES Measurement and Control Products for EARTH
Retired Product

This product is no longer available and has been replaced by: TX320. Some accessories, replacement parts, or services may still be available.

Sections: Other Accessories, Replacement Parts

This product is currently unavailable for orders.

Other Accessories
(hide details)
25316 GOES 11dBi Yagi RHCP Antenna w/Mounting Hardware
This RHCP (Right-Hand Circular Polarized) Yagi antenna has a gain of 11.0 dBic. The 25316 must be "aimed" at the proper azimuth and inclination to "hit" the assigned satellite. An adjustable mounting bracket is included.""
-L ft per antenna cable
This RG8/U, low-loss, coaxial cable has a characteristic impedence of 50 ohms. The COAXNTN provides two Type N male connectors for attaching the TX312 transmitter to the antenna.
Cable Length (hide details)
COAXNTN-L Antenna Cable RG8 w/2 Type N Male Connectors
This RG8/U, low-loss, coaxial cable has a characteristic impedence of 50 ohms. The COAXNTN provides two Type N male connectors for attaching the TX312 transmitter to the antenna.
16981 Surge Suppressor Kit for Satellite Transmitters w/Type N Female
The 16981 Surge Suppressor can be inserted between the COAXNTN cable and the TX312 transmitter to help protect the transmitter from electrical discharge being conducted down the antenna cable.
21212 Black Cold Shrink Tape, 10ft long Roll, 1in wide
This 10 ft (3.1 m) roll of 1"-wide black self-vulcanizing tape can help protect the antenna connections. After connecting the coaxial cables to the antenna, wrap the 21212 tape around the connectors that are exposed to the environment.
17992 30dB GPS Antenna 3.3V Jam- Resistant Active w/o Cable
The 17992 GPS antenna is both jam resistant and submersible for greater reliability under field conditions. It requires a 18017 antenna cable and mounting hardware (7623 pipe, CM202-series crossarm, and CM220 or NU-RAIL connector).
-L ft cable per sensor
The 18017 GPS Antenna Cable connects the 17992 GPS Antenna to the TX312 transmitter. The cable terminates in a TNC connector on one end and an SMA connector on the other end. The 18017 is required if the 17992 is ordered.
Cable Length (hide details)
18017-L GOES GPS Antenna Cable
The 18017 GPS Antenna Cable connects the 17992 GPS Antenna to the TX312 transmitter. The cable terminates in a TNC connector on one end and an SMA connector on the other end. The 18017 is required if the 17992 is ordered.
7623 3/4 IPS Aluminum Pipe w/ Threads, 10 inches long
An aluminum pipe is used to mount the GPS antenna to a crossarm. The pipe attaches to a crossarm via a 1049 NU-RAIL fitting or CM220 mount. The crossarm is then mounted to a tripod or tower.
1049 3/4 x 1 inch NURAIL Crossover Fitting
The 7623 pipe mentioned above fits into this NU-RAIL fitting. The fitting then attaches to one end of a CM202, CM204, or CM206 crossarm, and the crossarm mounts to a tripod or tower.
CM220 Right Angle Mounting Kit
The GPS antenna can be mounted to a crossarm via the CM220 mount and a 7623 pipe.
Replacement Parts
(hide details)
7845 3-Pin Screw Terminal Plug Connector .15 inch pitch Straight Wire Entry 16-28 AWG w/Threaded Flange GRN
This 3-pin green SDI-12 Connector may be purchased to replace a lost or damaged connector.
7843 2-Pin Screw Terminal Plug Connector .15 inch pitch Straight Wire Entry 16-28 AWG w/Threaded Flange GRN
This 2-pin Green Power Connector may be purchased to replace a connector that has been lost or damaged.
18133 TX320 or TX312 Power Cable, 2ft
The 18133 power cable connects the TX312 transmitter to the CH100 regulator. The cable contains the 18889 inline fuse that's listed below.