Synchronous Devices for Measurement

Expand your output and measurement capabilities

SDM-SIO1 Single-Channel Serial Input/Output Module

Single-Channel Serial Input/Output Module

The SDM-SIO1 module connects to the datalogger using the SDM port and communication protocol. The datalogger enables individual modules through...

SDM-AO4 4-Channel Continuous Analog Output Module

4-Channel Continuous Analog Output Module
  • Provides four independent continuous analog voltage outputs (0 to +5 Vdc)
  • Supports proportional control or strip charts
  • Conforms to EN55022-1:1995 and EN50082-1:1992
more »

SDM-CAN Datalogger to CANbus Interface

Datalogger to CANbus Interface
  • Supports CAN 2.0A and 2.0B active and passive modes
  • Supports up to 1 Mbaud data rate
  • Uses latest Philips SJA1000 CAN controller clocked at 16 MHz
more »

SDM-CD16AC 16-Channel ac/dc Relay Controller

16-Channel ac/dc Relay Controller
  • Consists of 16 ac/dc controllers for activating ac or dc devices
  • Provides contacts rated at 5 A @ 30 Vdc, 0.3 A @ 110 Vdc, 5 A @ 125 Vac, and 5 A @ 277 Vac
  • Includes LED that indicates when a port is active
more »

SDM-CD16D 16-Channel Digital Control Port Expansion Module

16-Channel Digital Control Port Expansion Module
  • Replaces the SDM-CD16
  • Intended for low voltage, low power applications not suitable for the SDM-CD16AC
  • Drives normal logic level inputs
more »

SDM-CD16S 16-Channel Solid State dc Relay Controller

16-Channel Solid State dc Relay Controller

The SDM-CD16S has 16 dc voltage outputs that can be switched on and off manually or under datalogger control. Separate inputs...

SDM-CVO4 4-Channel Current/Voltage Output Module

4-Channel Current/Voltage Output Module
  • Expands datalogger analog output capability
  • Provides four independent current or voltage outputs
  • Supports a voltage output range of 0 to 10000 mV with a resolution of 2.5 mV
more »

SDM-INT8 8-Channel Interval Timer

8-Channel Interval Timer
  • Allows individual programming for each of the eight channels
  • Includes an internal microprocessor that allows measurement independent of datalogger's execution interval
  • Detects voltage transitions
more »

SDM-IO16 16-Channel Input/Output Expansion Module

16-Channel Input/Output Expansion Module
  • Provides 16 digital I/O ports
  • Input configuration options: Monitor logic state, count pulses, measure signal frequency, and determine duty cycle
  • Output configuration options: Port set to 0 or 5 V by datalogger or source current up to 100 mA
more »

SDM-SIO4 4-Channel Serial I/O Interface

4-Channel Serial I/O Interface
  • Provides four configurable serial RS-232 ports
  • Allows connection to intelligent serial sensors, display boards, printers, satellite links, or applications where the data is transferred in a serial fashion
  • Supports 0-5 V logic levels
more »

SDM-SW8A 8-Channel Switch Closure Input Module

8-Channel Switch Closure Input Module
  • Provides eight individually configured channels
  • Measures reed switches, dry contacts, or slow voltage pulses
  • Supports single-pole double-throw (SPDT), single-pole single-throw (SPST), or voltage pulse measurements
more »



About Synchronous Devices for Measurement

The SDMs are a group of addressable peripherals that expand the datalogger's output and measurement capabilities. The datalogger controls the SDM output device by storing a value in a memory location which is then used by the SDM to set a voltage or relay. Measurement devices store data from sensors which are regularly read into the datalogger through a control port.

Dataloggers that are compatible with SDMs include our CR800, CR850, CR10X, CR1000, CR3000, CR5000, and CR7. Some SDM models such as the SDM-CAN are also used with the CR9000X. Please note that our CR200-series and CR510 dataloggers are not compatible.

SDM Overview