RF400
Ordering Information
This product is no longer available and has been replaced by: RF401. Some accessories, replacement parts, or services may still be available.
Sections:
Replacement Parts,
Services
This product is currently unavailable for orders.
| Replacement Parts | ||||
| 14291 | Field Power Cable 12Vdc Plug to Pigtail, 2ft | |||
|
The 14291 power cable allows the RF400 to be powered from a suitable 12 Vdc battery.
|
||||
| 15966 | Wall Charger 12Vdc 800mA Output, 100-240Vac 50-60Hz w/Barrel Plug, 6ft Cable | |||
|
A 15966 wall charger is required for ac power to serve as the power source for the RF400. This ac/dc transformer accepts inputs from 90 to 260 Vac @ 47 to 63 Hz, then outputs 12 Vdc @ 880 mA for use by the RF400. The 15966 is fitted with a cable and barrel plug to connect the transformer to the RF400; cable length is 6 ft.
|
||||
| 14162 | RF401, RF411, or RF416 Mounting Kit | |||
|
The 14162 kit attaches the radio to the backplate of an environmental enclosure.
|
||||
| 14201 | 900MHz 9dBd Yagi Antenna w/Type N Female & Mounting Hardware | |||
|
The 14201 is a high-gain (9 dBd), directional (Yagi) antenna suitable for outdoor use. It has a narrow beam width, so precise aiming is mandatory. The 14201 is useful for longer distances and when communicating only with one other station (due to narrow beam width). The antenna has a TYPE N female connector and requires an antenna cable to connect it to the radio.
|
||||
| 14221 | 900MHz 3dBd Omni Antenna w/Type N Female & Mounting Hardware | |||
|
The 14221 has the highest gain (3 dBd) of our omnidirectional antennas. It is suitable for base station use where you need to communicate with multiple stations located in different directions. It's rugged FM2 antenna mounts will accommodate a vertical pipe of up to 2.5" (6.5 cm) outside diameter. The antenna has a TYPE N female connector and requires an antenna cable to connect it to the radio.
|
||||
| 14204 | 900MHz 0dBd Omni 1/2 Wave Whip Antenna w/Right Angle & RPSMA Female | |||
|
The 14204 is a unity gain (0 dBd) omnidirectional antenna. This antenna must reside inside a building or enclosure. It's right angle knuckle joint can be oriented vertically or at right angles. The 14204 attaches directly to the RF400 (antenna cable not required).
|
||||
| 15731 | 900MHz 0dBd Omni 1/4 Wave Whip Antenna, Straight 2 inches Tall w/RPSMA Female | |||
|
The 15731 is a unity gain (0 dBd), straight, omnidirectional antenna that attaches directly to the RF400 (antenna cable not required). This antenna must reside inside of a building or enclosure.
|
||||
| 15730 | 900MHz 0dBd Omni 1/4 Wave Whip Antenna w/Right Angle & RPSMA Female | |||
|
The 15730 is a unity gain (0 dBd), right angle, omnidirectional antenna that attaches directly to the RF400 (antenna cable not required). This antenna must reside inside of a building or enclosure.
|
||||
| 15970 | 900MHz 1dBd Dipole Antenna w/Adhesive Mount & RPSMA Female 10ft Cable | |||
|
The 15970 is an omnidirectional antenna with a 1 dBd gain. It includes adhesive backing that adheres the antenna to a wall, rear-view mirror, window, or another suitable flat, non-conductive surface. A 10-ft cable is provided for attaching the antenna to the RF400. The 15930 must reside inside of a building or enclosure.
|
||||
| COAXRPSMA-L | Antenna Cable LMR195 w/Reverse Polarity SMA & Type N Male Connector | |||
|
Either this cable or the COAXNTN-L (see below) is required when using the 14201 or 14221 antennas. The COAXRPSMA-L is an LMR 195 cable that terminates in a type N Male connector on the "antenna end" and a Reverse Polarity SMA (RPSMA) connector on the "transceiver end." It is recommended for applications where the cable length is less than 10 feet.
|
||||
| Cable Length (hide details) | ||||
| -L | ft per antenna cable | |||
|
Either this cable or the COAXNTN-L (see below) is required when using the 14201 or 14221 antennas. The COAXRPSMA-L is an LMR 195 cable that terminates in a type N Male connector on the "antenna end" and a Reverse Polarity SMA (RPSMA) connector on the "transceiver end." It is recommended for applications where the cable length is less than 10 feet.
|
||||
| COAXNTN-L | Antenna Cable RG8 w/2 Type N Male Connectors | |||
|
Either this cable or the COAXRPSMA-L (see above) is required when using the 14201 or 14221 antennas. The COAXNTN-L is a low-loss RG8 coaxial cable that requires the 14462 surge suppressor to connect it to the RF400. The COAXNTN-L/14462 combination is recommended over the COAXRPSMA-L when the antenna cable is longer than 10 feet (as measured between the transceiver and the antenna) or when the RF400 is used in an environment susceptible to lightning or electrostatic buildup.
|
||||
| Cable Length (hide details) | ||||
| -L | ft per antenna cable | |||
|
Either this cable or the COAXRPSMA-L (see above) is required when using the 14201 or 14221 antennas. The COAXNTN-L is a low-loss RG8 coaxial cable that requires the 14462 surge suppressor to connect it to the RF400. The COAXNTN-L/14462 combination is recommended over the COAXRPSMA-L when the antenna cable is longer than 10 feet (as measured between the transceiver and the antenna) or when the RF400 is used in an environment susceptible to lightning or electrostatic buildup.
|
||||
| 14462 | Surge Suppressor Kit for 900 or 922MHz RPSMA Spread Spectrum Radios | |||
|
The 14462 Surge Suppressor Kit is required when using the COAXNTN cable. It helps protect the RF400 from electromagnetic surges.
|
||||
| 21212 | Black Cold Shrink Tape, 10ft long Roll, 1in wide | |||
|
This 10 ft (3.1 m) roll of 1"-wide black self-vulcanizing tape can help protect the connection of outdoor antennas. After connecting the coaxial cable to the antenna, wrap the tape around the connectors that are exposed to the environment.
|
||||
| 18663 | Data Cable Null Modem DB9 Male to Male, 1ft | |||
|
The 18663 is a 9-pin to 9-pin null modem cable used to connect the RF400 radio to the datalogger's RS-232 port.
|
||||
| 14413 | Data Cable RS-232 DB9 Male to DB25 Male, 6ft | |||
|
The 14413 is a straight-through DB9-to-DB25 male cable used to connect the RF400's RS-232 port to an SRM-5A Short Haul Modem, SDS-122 Serial Data Switch, or another 25-pin DTE RS-232 port.
|
||||
Resources and Links
Shipping Weights & Dims
Single Box Shipping Weight:
3.0 lbs
1.4 kg
Single Box Shipping Dimensions:
12" x 12" x 4"
30.5 x 30.5 x 10.2 cm
3.0 lbs
1.4 kg
Single Box Shipping Dimensions:
12" x 12" x 4"
30.5 x 30.5 x 10.2 cm
Feedback?