DCP200
Ordering Information
Allows communication from extremely remote locations
Educational Discounts: Yes Quantity Discounts: Yes Restockable: Yes Warranty: 1 year
| Model | Description | |||
| DCP200 | GOES Data Collection Platform | |||
| Enclosure Mounts (hide details) | ||||
| -NM | -NM No Enclosure Mounting | |||
|
The -NM option is shipped without brackets. The no bracket option is recommended for customers who wish to bolt the flanges of the enclosure to a flat surface, such as securing it to a wall with lag bolts. This option might also be appropriate for applications in which the enclosure will be "set on a table."
|
||||
| -MM | -MM Tripod Mast Mounting | |||
|
Order the "-MM" option if you want to mount your enclosure to the mast of one of our tripods or to a user-supplied pole with a 1.25" to 2.1" OD. A three-piece bracket attaches to the top of the enclosure and an identical three-piece bracket attaches to the bottom of the enclosure. Each bracket is attached to the mast or pole via a 2" u-bolt.
|
||||
| -TM | -TM Tower Mounting | |||
|
Order the "-TM" option if you want to mount your enclosure to a UT10, UT20, or UT30 tower. This mounting bracket option uses the same 3-piece brackets as the "-MM" option, except the pieces are rearranged so that the flanges are on the side of the bracket instead of in the middle. Four 1.5" u-bolts attach the brackets to the tower legs.
Please note that enclosures with the "-TM" option are shipped configured for the UT10 tower. UT20 and UT30 customers will need to: (1) remove the bolts attaching the bracket to the enclosure, (2) slide out the flange sections so that the distance between the center of each flange is 17", and (3) reattach the bracket to the enclosure using the original bolts. |
||||
| -PM | -PM Pole Mounting, 4-10in | |||
| Replacement Parts | ||||
| 7845 | 3-Pin Screw Terminal Plug Connector .15 inch pitch Straight Wire Entry 16-28 AWG w/Threaded Flange GRN | |||
|
This 3-pin, green connector is included on the TX312 transmitter for SDI-12 connections. The 7845 may be purchased to replace a lost or damaged connector.
|
||||
| 7843 | 2-Pin Screw Terminal Plug Connector .15 inch pitch Straight Wire Entry 16-28 AWG w/Threaded Flange GRN | |||
|
This 2-pin green power connector is included on the TX312 transmitter for power input. The 7843 may be purchased to replace a lost or damaged connector.
|
||||
| 6650 | Enclosure Ground 16 X 18 | |||
|
The 6650 consists of a 3-foot ground wire and lug connector.
|
||||
| 6571 | Enclosure Accessory Humidity Indicator Card | |||
|
The 6571 provides a visual reference of humidity level inside the enclosure. Colored circles change from blue to pink to indicate humidity levels of 30%, 40%, and 50% relative humidity. This humidity indicator card adheres to the inside wall of the enclosure.
|
||||
| 15598 | 3V Coil Cell Lithium Battery CR2016 | |||
|
This 3-V lithium battery fits inside of the CR295 datalogger. The 15598 powers the CR295's clock and SRAM when the primary 12 Vdc power supply is not connected. It needs to be periodically replaced.
|
||||
| 18133 | TX320 or TX312 Power Cable, 2ft | |||
|
This power cable connects the TX312 GOES Satellite Transmitter to the CH100 regulator. The 18133 contains the 18889 inline fuse that's listed below.
|
||||
| COAXNTN-L | Antenna Cable RG8 w/2 Type N Male Connectors | |||
|
The COAXNTN-L is an RG8/U, low-loss, coaxial cable with a characteristic impedence of 50 ohms. It has two Type N male connectors for attaching the TX312 transmitter to the antenna. The cable originally shipped with the DCP200 has a 12-foot length (i.e., COAXNTN-L12)
|
||||
| Cable Length (hide details) | ||||
| -L | ft per antenna cable | |||
|
The COAXNTN-L is an RG8/U, low-loss, coaxial cable with a characteristic impedence of 50 ohms. It has two Type N male connectors for attaching the TX312 transmitter to the antenna. The cable originally shipped with the DCP200 has a 12-foot length (i.e., COAXNTN-L12)
|
||||
| -L | ft cable per sensor | |||
|
The 18017 GPS Antenna Cable connects the 17992 GPS Antenna to the TX312 transmitter. The cable terminates in a TNC connector on one end and an SMA connector on the other end. The cable originally shipped with the DCP200 has a 10-foot length (i.e., 18017-L10).
|
||||
| 18017-L | GOES GPS Antenna Cable | |||
|
The 18017 GPS Antenna Cable connects the 17992 GPS Antenna to the TX312 transmitter. The cable terminates in a TNC connector on one end and an SMA connector on the other end. The cable originally shipped with the DCP200 has a 10-foot length (i.e., 18017-L10).
|
||||
| Cable Length (hide details) | ||||
Resources and Links
Related Products
Ships With
(1) 10873 9-Pin Female to 9-pin Male serial cable, 6 ft
(1) 1113 Flat-bladed screwdriver
(1) 17992 GPS Antenna 3.3 V, 30 dB
(1) 18017-L GPS Antenna Cable (10-foot length provided; i.e., 18017-L10)
(1) 18133 Power Cable, 2 ft (includes one 18889 Fuse)
(1) 18134 Transmitter Support Software
(2) 2376 Cable Tie Mounts
(1) 25316 GOES Yagi antenna
(1) 4905 Desiccant
(1) 6186 External Battery Cable
(1) 7363 Enclosure supply kit
(1) 7623 3/4" IPS aluminum pipe for mounting GPS antenna
(1) 8125 Flat-bladed screwdriver
(1) BP24 24-Ahr Sealed Rechargeable Battery
(1) CH100 Regulator
(1) CM220 Right Angle Mounting Kit
(1) COAXNTN-L GOES Antenna Cable (12-foot length provided; i.e., COAXNTN-L12)
(1) CR295X GOES Datalogger
(1) ENC16/18 Environmental Enclosure (with six cable entry seals and entry seals for antenna cables)
(1) SC12 Serial Cable
(1) SP20 20 W solar panel
(1) TX320 HDR GOES Satellite Transmitter
Feedback?