AVW200

Vibrating-Wire Interface

Greatly Reduces Signal Noise
Spectral analysis plus high resolution result in better readings

Image Gallery

Sections: Common Accessories, Replacement Parts

AVW200 Pricing Details
Educational Discounts: Yes Quantity Discounts: Yes Restockable: Yes Warranty: 1 year

Model	Description
AVW200	2-Channel Vibrating Wire Spectrum Analyzer Module
Temperature Ranges (hide details)
-ST	-ST Tested -25 to +50C
Every AVW200 is tested and guaranteed to perform within published specifications over the standard temperature range. Units are tested and shipped to standard operating range unless extended testing is specified.
-XT	-XT Tested -55 to +85C
Extended Temperature Testing over the -55° to +85°C range is also available. Individual units are subjected to performance tests at these extremes in a test chamber. Units that pass the tests are certified as extended temperature units.

Common Accessories (hide details)
CABLE3CBL-L	3-Conductor 22AWG Cable w/Drain
The CABLE3CBL-L is recommended to connect the AVW200 to a datalogger when SDI-12 is used. This 22-AWG, three-conductor cable has a Santoprene® jacket and an aluminum mylar shield.
CABLE3CBL-L Options (hide details)
-L	ft per cable
The CABLE3CBL-L is recommended to connect the AVW200 to a datalogger when SDI-12 is used. This 22-AWG, three-conductor cable has a Santoprene® jacket and an aluminum mylar shield.
Cable Termination Options (hide details)
-PT	-PT w/Tinned Wires
The CABLE3CBL-L is recommended to connect the AVW200 to a datalogger when SDI-12 is used. This 22-AWG, three-conductor cable has a Santoprene® jacket and an aluminum mylar shield.
-PW	-PW w/Pre-Wire Connector
The CABLE3CBL-L is recommended to connect the AVW200 to a datalogger when SDI-12 is used. This 22-AWG, three-conductor cable has a Santoprene® jacket and an aluminum mylar shield.
18663	Data Cable Null Modem DB9 Male to Male, 1ft
This 1-ft, null modem cable has 9-pin connectors on both ends. The 18663 can connect the AVW200's RS-232 port to the datalogger's RS-232 port.
17855	Data Cable RS-232 or CS I/O DB9 Male to Pigtail, 2ft
One end of this cable is fitted with a 9-pin connector, and the other end terminates in pigtails. The 17855 is used to connect the AVW200's RS-232 port to a pair of control ports on a CR800, CR850, CR1000, or CR3000.

Replacement Parts (hide details)
3768	2-Pin Screw Terminal Plug Connector .2 inch pitch Straight Wire Entry 12-24 AWG Green Marked G 12V
This green, plug-in power connector is shipped attached to the AVW200. The 3768 provides screw terminals for connecting the 12V and GND wires of the 19246 power cable. The other end of the 19246 power cable connects to the 12V and G terminals of a datalogger or power supply.
20581	Terminal Connector Plug .2 Inch Pitch 15-Pin Straight Wire Entry 12-24 AWG Green Marked AVW200 Series
The 20581 provides screw terminals for connecting the sensor(s) and multiplexer(s) to the AVW200. This green, plug-in connector may be purchased to have a spare terminal strip or as a replacement item if the strip has been lost or damaged.
19246	AVW200-series To Datalogger Power Cable, 24 Inches
The 19246 connects the AVW200 with the 12V and G terminals of a datalogger or power supply. This screw terminal is shipped with the AVW200 and available as a replacement part.
10873	9-Pin Female to 9-Pin Male Serial Data Cable, 6ft
This RS-232 cable connects the AVW200 with a PC. The AVW200 is connected to a PC during configuration and troubleshooting. The 10873 is shipped with the AVW200 and available as a replacement part.